background image

 

All-in-one solar charge inverter    V11                                                                                                                                                               27 

Parameter 

no. 

Parameter 

name 

Settings 

Description 

10 

Battery boost 

charge time 

[10] 120 

default

 

Boost charge maximum time setting, which means the 
maximum charging time to reach the set voltage of 
parameter [09] during constant-voltage charging. The 
setting range is 5min~900min, with a step of 5 
minutes. It is valid for user-defined battery and 
lithium battery. 

11 

Battery floating 

charge voltage 

[11] 55.2V 

default

 

Floating charge voltage, setting range: 48V~58.4V, 
step: 0.4V, valid when battery type is user-defined. 

12 

Battery over 

discharge 

voltage (delay 

off) 

[12] 42V 

default

 

Over-discharge voltage; when the battery voltage is 
lower than this judgment point, delay the time set by 
parameter [13] and turn off inverter output. Setting 
range is 40V~48V, with a step of 0.4V. It is valid for 
user-defined battery and lithium battery. 

13 

Battery over 

discharge delay 

time 

[13] 5S 

default

 

Over-discharge delay time; when the battery voltage 
is lower than the parameter [12], the inverter output 
will be turned off after the time set by this parameter 
is delayed. The setting range is 5S~55S, with a step of 
5S. It is valid for user-defined battery and lithium 
battery. 

14 

Battery under 
voltage alarm 

[14] 44V 

default

 

Battery undervoltage alarm point; when the battery 
voltage is lower than the point, an undervoltage 
alarm is given, and the output is not turned off; the 
setting range is 40V~52V, with a step of 0.4V. It is 
valid for user-defined battery and lithium battery. 

15 

Battery 

discharge limit 

voltage 

[15] 40V 

default

 

Battery discharge limit voltage; when the battery 
voltage is lower than the point, the output is turned 
off immediately; the setting range is 40V~52V, with a 
step of 0.4V. It is valid for user-defined battery and 
lithium battery. 

16 

Battery 

equalization 

enable 

[16] DIS 

Equalizing charge is disabled 

[16] ENA 

default

 

Equalizing charge is enabled, only valid for vented 
lead-acid battery and sealed lead-acid battery 

17 

Battery 

equalization 

voltage 

[17] 58.4V 

default

 

Equalizing charge voltage; setting range: 48V~58.4V, 
with a step of 0.4V; valid for vented lead-acid battery 
and sealed lead-acid battery 

Содержание HF4830S60-145








































Отзывы: