Parker Porter MPC Series Скачать руководство пользователя страница 29

 

- 27 - 

CERTIFICATE OF WARRANTY 

 
 
 
THIS WARRANTY IS GIVEN IN PLACE OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, OF 
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR OTHERWISE. NO PROMISE OR 
STATEMENT MADE BY ANY REPRESENTATIVE OR AUTHORIZED DEALER OF PARKER HANNIFIN 
CORP. SHALL CONSTITUTE A WARRANTY BY PARKER HANNIFIN CORP.  
 
Parker Hannifin Corporation, Porter Instrument Division, warrants this equipment to be free from defects 
in workmanship and materials, when used in accordance with applicable specifications and with 
appropriate maintenance, for one (1) year from date of delivery to the customer, unless otherwise 
specified in writing.  
 
Equipment which malfunctions may be returned, shipment prepaid, to Parker Hannifin Corporation, Porter 
Instrument Division, for test and evaluation. Equipment determined to be defective and in warranty will be 
repaired or replaced at no charge to the customer. Equipment out of warranty will be evaluated, and if the 
equipment does not meet original specifications and calibration, the customer will be notified of the costs 
before proceeding with repair or replacement. Repaired equipment will be warranted ninety (90) days 
from date of delivery to the customer or for the balance of the original warranty, whichever is longer. 
 
Failures due to shipping damage, accident, misuse, improper mechanical or electrical installation or 
operation, or internal clogging or corrosion due to use of contaminated fluids or inadequate system 
purging are excluded from warranty coverage. 
 
Parker Hannifin Corporation’s obligation for breach of this warranty, or for negligence or otherwise, shall 
be strictly and exclusively limited to the repair or replacement of the equipment. This warranty shall be 
void as to any equipment on which the serial number, if applicable, has been altered, defaced, or 
removed. Parker Hannifin Corporation shall under no circumstances be liable for incidental or 
consequential damages. 
 
No other promise or statement about the equipment by any representative or authorized dealer of Parker 
Hannifin Corporation shall constitute a warranty by Parker Hannifin Corporation or give rise to any liability 
or obligation of Parker Hannifin Corporation. 

Содержание Porter MPC Series































Отзывы: