Parker ALIGN-MG-JA Скачать руководство пользователя

Страница: 4 / 25

INSTALLATION, OPERATION, AND MAINTENANCE MANUAL ALIGN™ MULTI-GAS GENERATOR

WARRANTY (NORTH AMERICA ONLY)

FOR INFORMATION CONTACT YOUR LOCAL REPRESENTATIVE

Parker Hannifin guarantees to the original purchaser of this product, that if the product fails

or is defective within 12 months from the date of purchase, when this product is operated and maintained

according to the instructions provided with the product, then Parker guarantees, at Parker’s option, to re

place the product, repair the product, or refund the original price for the product. This warranty applies only

to defects in material or workmanship and does not cover: wear components on compressors, routine main

tenance recommended by the instructions provided with this product, or filter cartridges. Any modification of

the product without written approval from Parker will result in voiding this warranty. Complete details of the

warranty are available on request. This warranty applies to units purchased in North America.

COMPRESSOR LIMITED WARRANTY

COMPRESSOR 3 YEAR / 10,000 HOUR EXTENDED PARTS LIMITED WARRANTY -

Compressor Manufacturer warrants each Compressor Pump or Scroll Air-End against defects in material or

workmanship from the date of purchase for a period of Three years or 10,000 hours, whichever may occur

first. This warranty applies to the exchange of part(s) of the compressor pump or air-end found to be defec

tive by an Authorized Service Center.

COMPRESSOR 1 YEAR / 5,000 HOUR INLET TO OUTLET LIMITED WARRANTY - Compressor

Manufacturer warrants each Compressor Unit, System, Pump, or Air-End against defects in material or

workmanship from the date of purchase for a period of One Year or 5,000 Hours, whichever may occur first.

This warranty applies to the exchange of defective component part(s) and labor performed by an Authorized

Service Center.

Complete details of the Warranty are available on request.

1. WARRANTY

IOM_PKR_Align Multi-Gas Generator_022021.indd 4

2/17/2021 1:11:40 PM

Содержание ALIGN-MG-JA


























Результаты поиска

Содержание ALIGN-MG-JA

Отзывы:

Похожие инструкции для ALIGN-MG-JA

Бренды по названию

Популярные бренды

Parker ALIGN-MG-JA, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ALIGN-MG-JA

Отзывы:

Похожие инструкции для ALIGN-MG-JA

Бренды по названию

Популярные бренды