Paradyne T1 Access Mux 916x Скачать руководство пользователя страница 49

Страница: 49 / 326

User Interface

4-5

9161-A2-GH30-30

April 1998

Navigating the Screens

You can navigate the screens by:

Using keyboard keys

Switching between the two screen work areas

Using screen function keys

Keyboard Keys

Use the following keyboard keys to navigate within the screens.

To . . .

Press . . .

Move cursor between the screen area and
the screen function keys area

Ctrl-a

Return to the previous screen

Esc

Move cursor to the next field

Right Arrow (on same screen row), or
Tab (on any screen row)

Move cursor to the previous field

Left Arrow (on same screen row), or
Ctrl-k

Move cursor one position to the left. If the
cursor is at the beginning of a field,
Backspace has no effect.

Backspace

Move cursor to the first character of the
previous field (backtab)

Ctrl-k

Display the next valid value for the field

Spacebar

Delete character that the cursor is on

Delete (Del)

Move cursor up one field within a column on
the same screen

Up Arrow or Ctrl-u

Move cursor down one field within a column
on the same screen

Down Arrow or Ctrl-d

Move cursor one character to the right if in
edit mode

Right Arrow or Ctrl-f

Move cursor one character to the left if in edit
mode

Left Arrow or Ctrl-b

Redraw the screen display, clearing
information typed in but not yet entered

Ctrl-l

Accept entry or display valid options on the
last row of the screen when pressed before
entering data or after entering invalid data

Return (Enter)

Содержание T1 Access Mux 916x







































































































































































































































































































































Результаты поиска

Содержание T1 Access Mux 916x

Отзывы:

Похожие инструкции для T1 Access Mux 916x

Бренды по названию

Популярные бренды

Paradyne T1 Access Mux 916x, Техническое описание

Результаты поиска

Содержание T1 Access Mux 916x

Отзывы:

Похожие инструкции для T1 Access Mux 916x

Бренды по названию

Популярные бренды