Paradyne T1 Access Mux 916x Скачать руководство пользователя страница 208 | Manualshive

Страница: 208 / 326

background image

Troubleshooting

9-26

9161-A2-GH30-30

April 1998

Remote Loopbacks

The remote loopback up codes (which put a remote device in loopback mode)
and down codes (which take a remote device out of loopback mode) are in-band
codes that allow remote control of a device.

H

Network loopbacks are defined in AT&T TR 62411.

H

The LLB up code invokes a line loopback in the remote unit while the LLB
down code terminates the line loopback in the remote unit.

The following tests cannot be running when a remote loopback test is initiated:

H

All loopbacks on this Network or DSX-1 interface

H

Send Pattern Test on this interface or any data port assigned to this interface

H

Send Remote Line Loopback on this interface

H

Send V.54 or Send FT1 Loopback on any data port assigned to this interface

H

Data Channel Loopback on any data port assigned to this interface

"

Procedure

To start and stop a Remote Loopback:

1. Follow this menu selection sequence:

Main Menu

→

Test

→

Network Tests

2. Select the desired Network interface (1 for 9161 NAM, 1 or 2 for 9261 NAM).

3. Select the code Up or Down in the Send Line Loopback field.

4. Highlight Send under Command in the Send Line Loopback row. Then, press

Return to start the test. The code will be sent for 10 seconds.

«
...
206
207
208
209
210
...
»

Содержание T1 Access Mux 916x







































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для T1 Access Mux 916x

Verizon DSL-2750B

Бренд: D-Link Страницы: 6

Бренд: D-Link Страницы: 10

Бренд: D-Link Страницы: 38

Ray 3 Plus Client

Бренд: Sun Microsystems Страницы: 6

Supero SAS-826A

Бренд: Supero Страницы: 16

StorageWorks AIT 35GB AutoLoader

Бренд: Compaq Страницы: 4

Бренд: Rosewill Страницы: 3

COMMWARE ECHO 5G

Бренд: pivotal Страницы: 2

Бренд: A4Tech Страницы: 8

Turbo NAS TVS-71 Series

Бренд: QNAP Страницы: 51

Бренд: Longshine Страницы: 35

Бренд: Aaeon Страницы: 61

Бренд: Gigabyte Страницы: 18

FastTrak TX4000

Бренд: Promise Technology Страницы: 76

Бренд: Avenview Страницы: 28

Бренд: Accton Technology Страницы: 78

Бренд: Kontron Страницы: 62

Бренд: Renesas Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды