Paradyne T1 Access Mux 916x Скачать руководство пользователя страница 188

Страница: 188 / 326

SIG

OOF

ALM

SIG

OOF

ALM

9109 DSX

OUT

DSX 2

DSX 1

DSX 2 MON

DSX 1 MON

DSX1

DSX2

97-15642-01

Test

Jacks

LEDs

Troubleshooting

9-6

9161-A2-GH30-30

April 1998

Dual DSX APM LEDs

DSX 1 and DSX 2 Interface LEDs

Label

Indication

Color

What It Means

SIG

Signal

Green

– A recoverable signal is present on the

DSX1/DSX2 interface.

OFF – The signal cannot be recovered from

the DSX1/DSX2 interface. An LOS
condition exists.

OOF

Out of Frame

Yellow

– At least one OOF was detected during

the sampling period.

OFF – No OOFs were detected during the

sampling period.

ALM

Alarm

Yellow

– An alarm condition is present on the

DSX1/DSX2 interface.

Current alarm conditions:

Loss of Signal ( LOS )

Loss of Frame (LOF)

Excessive Error Rate (EER)

Yellow

Alarm Indication Signal (AIS)

OFF – No alarm condition is present on the

DSX1/DSX2 interface.

General Status LED

Label

Indication

Color

What It Means

Power and
Operational
Status

Green

– The APM has power and is

operational.

OFF – The APM is in a local self-test, or there

is a failure.

Содержание T1 Access Mux 916x







































































































































































































































































































































Результаты поиска

Содержание T1 Access Mux 916x

Отзывы:

Похожие инструкции для T1 Access Mux 916x

Бренды по названию

Популярные бренды

Paradyne T1 Access Mux 916x, Техническое описание

Результаты поиска

Содержание T1 Access Mux 916x

Отзывы:

Похожие инструкции для T1 Access Mux 916x

Бренды по названию

Популярные бренды