Paradyne T1 Access Mux 916x Скачать руководство пользователя страница 153

Страница: 153 / 326

Displaying System Information

7-11

9161-A2-GH30-30

April 1998

Displaying Port Assignments

Use the Port Assignments Display screen to display port assignment information
for each voice and data port on the NAM and APMs.

Use the following menu sequence to display port assignment information.

Main Menu

→

Status

→

Cross Connect Status

→

Port Assignment Display

The following information is available for viewing.

View this field . . .

To find the . . .

Slot

Slot number.

Type

Type of NAM or APM occupying the slot. Possible
values are:

T1 NAM – T1 NAM.

Sync Data – 4-port synchronous data APM.

DSX-1 – 2-port DSX APM.

E&M Voice – 8-port E&M APM.

FXO Voice – 8-port FXO Voice APM.

FXS Voice – 8-port FXS Voice APM.

OCU (2) – 2-port OCU-DP APM.

OCU (6) – 6-port OCU-DP APM.

Empty – The slot is empty.

Misconfig – The slot contains a misconfigured APM.

Unsupport – The slot contains an unrecognized APM.

Failed – The slot contained an APM that has been
removed or is no longer operational.

Assignment

Port assignment. Possible values are:

Blank – slot is empty or port does not exist on the NAM
or the APM.

Disable – The port is disabled.

Unassgn – The port is unassigned.

Net

n – The port is assigned to the Network Interface 1

or 2.

DSX

ss-p – The port is assigned to the DSX-1 interface

in slot

ss (always 01), port p on a clear channel time

slot. Ports cannot be cross-connected to the DSX APM.

ssPp – The port-to-port assignment of the slot (ss)

and sync data port (

p) shown in this field.

Содержание T1 Access Mux 916x







































































































































































































































































































































Результаты поиска

Содержание T1 Access Mux 916x

Отзывы:

Похожие инструкции для T1 Access Mux 916x

Бренды по названию

Популярные бренды

Paradyne T1 Access Mux 916x, Техническое описание

Результаты поиска

Содержание T1 Access Mux 916x

Отзывы:

Похожие инструкции для T1 Access Mux 916x

Бренды по названию

Популярные бренды