Paradyne T1 Access Mux 916x Скачать руководство пользователя страница 258

Страница: 258 / 326

SNMP Traps

C-6

9161-A2-GH30-30

April 1998

Interface

For These Tests

enterpriseTestStart/Stop
Variable-Bindings

OCU Ports

ifIndex (RFC 1573)

ifAdminStatus
(RFC 1573)

ifOperStatus (RFC 1573)

fType (RFC 1573)

devOcuTestType
(devOcu.mib)

Latching CSU and DSU
Loopbacks

Nonlatching CSU and DSU
Loopbacks

OCU Loopback

DS-0 Loopback

Line Loopback

Data Loopback

Remote Latching CSU, DSU
and OCU Loopbacks

Remote Nonlatching CSU,
DSU and OCU Loopbacks

Send pattern tests

Monitor pattern tests

Voice Ports

ifIndex (RFC 1573)

ifAdminStatus
(RFC 1573)

ifOperStatus (RFC 1573)

fType (RFC 1573)

devVoiceTestType
(devVoice.mib)

Digital Loopback

Analog Loopback

Line Loopback

Send DRS tone to T1 interface
and user

Send quiet tone to T1
interface and user

Monitor pattern tests

Содержание T1 Access Mux 916x







































































































































































































































































































































Результаты поиска

Содержание T1 Access Mux 916x

Отзывы:

Похожие инструкции для T1 Access Mux 916x

Бренды по названию

Популярные бренды

Paradyne T1 Access Mux 916x, Техническое описание

Результаты поиска

Содержание T1 Access Mux 916x

Отзывы:

Похожие инструкции для T1 Access Mux 916x

Бренды по названию

Популярные бренды