Paradyne T1 Access Mux 916x Скачать руководство пользователя страница 132

Страница: 132 / 326

Setting Up

5-78

9161-A2-GH30-30

April 1998

Setting Up and Placing a Call

Configure your external device. Then, use the Call Setup screen to:

Look up the desired telephone number

Dial a call

Disconnect a call

Procedure

1. Follow this menu selection sequence:

Main

→

Control

→

Call Setup

2. The Control menu appears. Select Call Setup and press Return.

3. The Call Setup screen appears. Enter the number of the directory containing

the desired telephone number in the Directory Number field. The telephone
number appears in the Directory Phone Number field. See

Displaying

Directory Numbers

and

Changing Directory Numbers

in Chapter 9,

Troubleshooting and Maintenance, for information about the call directory.

4. Select Dial and press the Enter key to initiate dialing.

5. To end the call, select Disconnect and press the Enter key.

Содержание T1 Access Mux 916x







































































































































































































































































































































Результаты поиска

Содержание T1 Access Mux 916x

Отзывы:

Похожие инструкции для T1 Access Mux 916x

Бренды по названию

Популярные бренды

Paradyne T1 Access Mux 916x, Техническое описание

Результаты поиска

Содержание T1 Access Mux 916x

Отзывы:

Похожие инструкции для T1 Access Mux 916x

Бренды по названию

Популярные бренды