Paradyne Jetstream CPX-1000 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 240

background image

5. CPX-1000 Configuration

1000-A2-GB22-10

5-2

June 2005

CPX-1000
Configuration
Profile

The CPX-1000 is preprovisioned with a standard configuration
profile.

Since most of the CPX-1000 configuration parameters cannot be
changed after Interface Groups and IADs are provisioned, modify
the CPX-1000 configuration at startup.

Table 5–1

lists the configuration parameters needed for configuring

the CPX-1000 in JetCraft.

Table 5–1. CPX-1000 Configurable Parameters

CPX Parameter

Description

ID

An identifier associated with the CPX-1000, consists of 4–63
alphanumeric characters (e.g., JET1). No spaces, underlined
characters, etc. allowed.

Name

A name for the CPX-1000 that consists of up to 63 alphanumeric
characters (e.g., JETSET). No spaces, underlined characters, etc.
allowed.

Use this name for differentiating CPX-1000s, error reporting, and
when creating an IAD.

IP Address

The 32-bit Internet Protocol address assigned to the CPX-1000.

Default Gateway

The IP address that allows the CPX-1000 to be addressed over a
LAN or WAN.

Subnet Mask

The 32-bit identifier that allows the IP address of the CPX-1000 to
be used with multiple connections.

Administrative State

JetCraft administrative service-affecting state of CP cards and
ports. Options are:

Unlocked: Capable of service

Locked: Restricted from service (card is in the shelf, but
JetCraft or JetVision administrators restricted it from
service)

Operational State

The operational state of the CPX-1000 cards and ports. Options
are:

Enabled

Disabled

«
...
50
51
52
53
54
...
»

Содержание Jetstream CPX-1000

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Jetstream CPX-1000

Бренд: EAW Страницы: 36

Бренд: TANDBERG Страницы: 66

Content Server None

Бренд: TANDBERG Страницы: 14

XN200 series XN-004-A1

Бренд: Xtore Страницы: 4

XN200 series XN-004-A1

Бренд: Xtore Страницы: 7

AlliedWare Plus 5.2.1

Бренд: Allied Telesis Страницы: 1294

Бренд: M-Audio Страницы: 5

Membrain Software

Бренд: SanDisk Страницы: 14

BJ0NJML - Service And Asset Management

Бренд: IBM Страницы: 330

MetaFrame MetaFrame Presentation Server

Бренд: Citrix Страницы: 97

FLASH 8-LEARNING ACTIONSCRIPT 2.0 IN FLASH

Бренд: MACROMEDIA Страницы: 830

Бренд: Brocade Communications Systems Страницы: 47

WISE INSTALLATION EXPRESS 7.0 SP2

Бренд: Symantec Страницы: 50

Бренд: Multitech Страницы: 96

Бренд: 360 Systems Страницы: 58

Бренд: VERITAS Страницы: 580

Trillium Lane Labs

Бренд: DigiDesign Страницы: 114

Бренд: 3Ware Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды