Paradyne Jetstream CPX-1000 Скачать руководство пользователя страница 214 | Manualshive

Страница: 214 / 240

background image

12. Integrated Monitoring

1000-A2-GB22-10

12-2

June 2005

Launching
Integrated
Monitor

Integrated Monitor uses colors as visual cues to indicate the
different states of each entity: green for active, blue for standby,
and gray indicates that connection is down.

To launch the Integrated Monitor:

Click the CPX-1000, and select

Integrated Monitoring

from

the Configuration menu.

– Or –

Right-click the CPX-1000, and select

Integrated Monitoring

from the pop-up menu.

The Integrated Monitor view similar to

Figure 12–1

opens in a

separate window.

Table 12–1.Integrated Monitor Operation

Entities

Monitoring

…

GR-303 Interface Groups

It provides the physical mapping of the TMC/EOC/
TMCPPS/EOCPPS with the DS1 # to an IG (i.e., T1 IG) and
the physical port to logical channel (i.e., STS IG). The Lock
symbol indicates that the particular channel is down as it has
been locked.

the operational state of each TMC and EOC (i.e., Up or
Down)

the standby state of each TMC and EOC (i.e., active or
standby)

the redundancy state of each TMC and EOC (i.e., primary or
secondary)

Protection Groups
(Network and PSTN)

the operational state of the Protection Groups (i.e., Up or
Down)

the standby state of the Protection Groups (i.e., active or
standby)

the redundancy state of the Protection Groups (i.e., primary
or secondary)

CPX-1000

the connection status of each entity

«
...
212
213
214
215
216
...
»

Содержание Jetstream CPX-1000

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Jetstream CPX-1000

e-control Database Manager

Бренд: Crestron Страницы: 94

Бренд: Alcatel Страницы: 4

Бренд: COMPRO Страницы: 36

Applied Vision 4

Бренд: Ken A Vision Страницы: 16

BACKUP EXEC 11D

Бренд: Symantec Страницы: 18

ALTIRIS IT MANAGEMENT SUITE 7.0 MR2 - S

Бренд: Symantec Страницы: 14

ALTIRIS DEPLOYMENT SOLUTION 7.1

Бренд: Symantec Страницы: 90

VSHIELD APP 1.0.0 UPDATE 1 - API

Бренд: VMware Страницы: 144

Vigil Server V5.00

Бренд: 3xLogic Страницы: 134

BREEZE-FOR MEETING PRESENTERS

Бренд: MACROMEDIA Страницы: 96

Бренд: Xerox Страницы: 308

Microsoft Exchange Integration V 11.8

Бренд: TANDBERG Страницы: 39

Бренд: TANDBERG Страницы: 19

Бренд: Iqinvision Страницы: 60

Digital Vintage Reverb DVR2

Бренд: TC Electronic Страницы: 16

ProBook 5320m - Notebook PC

Бренд: HP Страницы: 147

Бренд: HP Страницы: 38

ProBook 4325s - Notebook PC

Бренд: HP Страницы: 160

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды