Paradyne Jetstream CPX-1000 Скачать руководство пользователя

Страница: 230 / 240

C. Alarm Summary

1000-A2-GB22-10

C-2

June 2005

CP card

Lost connection to a CP

Indicates lost connection to
CP.

Major

CME

CP lost heartbeat to peer

Indicates CP lost heartbeat
to peer CP.

Major

CORE

CP found the peer CP faulty

Indicates CP found the peer
CP faulty.

Major

CORE

CP detected that the peer
CP has been removed

Indicates CP has detected
the removal of peer CP.

Major

CORE

IAD

IAD <name> unknown
alarm

Indicates the IAD has not
been initialized or
recognized.

Major

CORE

Lost link with IAD <name>

Indicates a lost link with the
IAD.

Major

CORE

Provisioned ports <ID> are
greater than the reported
ports <ID>

Indicates the number of
provisioned ports is greater
than the number of
reported ports.

Major

CME

Voice Quality Alarm

VQA is triggered whenever
ATM overruns and
underruns exceed
predefined thresholds

Minor

CORE

IAD Ports

IAD <name> port <ID>
alarm

Indicates the IAD port has
not been initialized or
recognized.

Major

CORE

Table C–1. Alarm Summary (Continued)

Affected

Element

Alarm Message

Description

Severity

Triggered

Содержание Jetstream CPX-1000

















































































































































































































































Результаты поиска

Содержание Jetstream CPX-1000

Отзывы:

Похожие инструкции для Jetstream CPX-1000

Бренды по названию

Популярные бренды

Paradyne Jetstream CPX-1000, Руководство пользователя

Результаты поиска

Содержание Jetstream CPX-1000

Отзывы:

Похожие инструкции для Jetstream CPX-1000

Бренды по названию

Популярные бренды