Paradyne Jetstream CPX-1000 Скачать руководство пользователя

Страница: 130 / 240

9. IAD Profiles and IADs Provisioning

1000-A2-GB22-10

9-20

June 2005

Step 17

Click to select the values for the following IAD port parameters
from the associated drop-down list.

Admin State

Signaling

Compression

Echo Cancellation

The Signaling type can be set as Ground for LES CAS Ground Start
IADs. Do not select 16 kbps compression for LES CAS IADs.

Step 18

Type the starting CRV in the

Starting CRV

field.

Step 19

Click

. The IAD Creation Summary screen appears, listing the

IAD parameters you have just created (

Figure 9–17

Figure 9–17. IAD Creation Summary Screen

Step 20

Review the IAD parameters.

If parameters are correct, click

Finish.

Note

The number of ports is dependent upon the IAD Profile.
The field is automatically populated based on the profile
selection.

Содержание Jetstream CPX-1000

















































































































































































































































Результаты поиска

Содержание Jetstream CPX-1000

Отзывы:

Похожие инструкции для Jetstream CPX-1000

Бренды по названию

Популярные бренды

Paradyne Jetstream CPX-1000, Руководство пользователя

Результаты поиска

Содержание Jetstream CPX-1000

Отзывы:

Похожие инструкции для Jetstream CPX-1000

Бренды по названию

Популярные бренды