Paradyne Jetstream CPX-1000 Скачать руководство пользователя страница 195

Страница: 195 / 240

June 2005

11-13

1000-A2-GB22-10

11. Maintenance and Services

Hot Swapping
CP and HSC
Cards

HSC cards are paired with CP cards. After the HSC card is
replaced, pairing with the CP card is automatically restored.

To hot swap CP and HSC cards:

Step 1

Click the CP card icon from the Tree or Shelf view.

If hot swapping an active CP or HSC card, continue with

Step 2

If hot swapping a standby CP or HSC card, continue with

Step 3

Step 2

Perform switchover to place the active card in standby (

Performing

a CP Switchover

on page

11-11

Step 3

Place the CP card to the Locked state (

Changing CP Card States

page

11-9

Step 4

Select

Remove Resources

from the Configuration menu. A

prompt appears, asking if you want to remove all resources
associated with the card.

Step 5

Click

Yes

. The card is removed from the Tree and Shelf views.

Step 6

Remove the physical CP card, followed by its corresponding HSC
card, from the CPX-1000 shelf.

Step 7

Insert the HSC card, followed by the CP card, and lock them in
place using the card ejectors. (Continue with

Step 9

if this is a

standby CP or HSC card.)

Step 8

Select

Refresh

CPX

from the File menu. The new cards appear in

the Tree and Shelf views.

Step 9

Place the CP card to the Unlocked state (

Changing CP Card States

on page

11-9

Note

Make sure to put on an anti-static wrist wrap when hot
swapping cards. Refer to

CPX-1000 Voice Services

Platform Installation and Operation

for more information.

Содержание Jetstream CPX-1000

















































































































































































































































Результаты поиска

Содержание Jetstream CPX-1000

Отзывы:

Похожие инструкции для Jetstream CPX-1000

Бренды по названию

Популярные бренды

Paradyne Jetstream CPX-1000, Руководство пользователя

Результаты поиска

Содержание Jetstream CPX-1000

Отзывы:

Похожие инструкции для Jetstream CPX-1000

Бренды по названию

Популярные бренды