Paradox MG5000+ Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 55

background image

/ Installation Guide

9

PCB Layout

To provide maximum
lightning protection we
strongly recommend having
separate earth connections
for the dialer and zone
ground terminals.

Disconnect
telephone line
before servicing.

1 Four-pin connector can be used for quick installation of a keypad
2

LEDs

AC LED:
•

ON = AC present; OFF = AC missing

Battery LED:
•

ON = Battery present; OFF = No battery

STAT LED:
•

Flashing once per second = Normal operation

AUX LED:
•

ON = Aux present; OFF = Aux off

RF-RX LED:
•

FLASH ON = RF message reception

RF-TX LED:
•

FLASH ON = RF transmission from panel

3 Panel reset
4 Serial: Used for connecting the IP Internet Module/PCS (Data); also used for

In-Field Firmware upgrade through a 307USB Direct Connect Interface

5 Antenna
6 RS485 connector
7 Zone Input

8 PGMs: these jumpers allows you to choose whether the solid state relay

PGMs are grounded (-), or give out 12V (+).

9 Backup Battery connections

10 The

BELL

output will shutdown if the current exceeds 3A

11 AWG #14 single conductor solid copper wire
12 Ground clamp
13 Cold water pipe grounding
14 To ground
15 Keypad zone configuration
16 Zone connection, if EOL is enabled, see section

[706]

option 2,

on

page page 28

17 To connect additional wiring to auxiliary power, use the red (

+

) and black

(

-

) keypad connectors; auxiliary power will shut down if current exceeds

3A; if the auxiliary output is overloaded and shuts down, you must
disconnect all loads from the output for at least 10 sec. before
reconnecting any load back to the auxiliary output

Do not cut, bend, or alter
the antenna, and ensure
that electrical wires or other
type of wires do not cross
over it, as this may affect
signal reception. Do not
install the antenna near
wires as it may cause
interference.

40 VA transformer strongly recommended.

Max. number of keypads: 15 keypads
Max. aux. current: 700 mA
Max. distance of bus module from panel: 76 m (250 ft.)
Max. total run of wire: 230 m (750 ft.)

This equipment must be installed and maintained by qualified service personnel only.

The sum of the current drawn from the

BELL

and

AUX

must be limited to 1.3A. Exceeding this limit will overload the panel power supply

and lead to complete system shutdown.

«
...
7
8
9
10
11
...
»

Содержание MG5000+
























































Отзывы:

Нет отзывов

Похожие инструкции для MG5000+

Vb-C60 - Ptz Network Camera

Бренд: Canon Страницы: 76

Бренд: Nelson Страницы: 18

Бренд: Nelson Страницы: 150

Бренд: NELLYS SECURITY Страницы: 15

Water Jet Lightning

Бренд: Oase Страницы: 28

Бренд: Oase Страницы: 9

Бренд: GBO Technology Страницы: 103

MCX-A10 - MusicCAST Network Audio Player

Бренд: Yamaha Страницы: 56

Бренд: NAPCO Страницы: 80

Бренд: ACS Страницы: 64

Бренд: Velleman Страницы: 18

Бренд: i3 International Страницы: 28

Бренд: Watts Страницы: 10

Бренд: Huviron Страницы: 56

Бренд: Black Страницы: 24

Бренд: Teac Страницы: 23

Бренд: Axis Страницы: 42

Бренд: Real-El Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды