Paradox MG5000+ Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 55

background image

/ Installation Guide

41

Example:

The system is armed and zone 1 has been breached causing an alarm. If options

[5]

and

[7]

are OFF and option

[6]

is ON in section

[802]

, the control panel

will attempt to communicate with MSTN 2.

Account Numbers

Section

[811]

: Partition 1, Section

[812]

: Partition 2

All report codes are preceded by a 4-digit or 3-digit Partition Account Number to ensure correct identification in a partitioned system. Partition account numbers
can be any hexa-digit from 1 to F. To enter a 3-digit account number, simply press the

[

SLEEP

]

key followed by a 3-digit account number. Also, when using 3-digit

account numbers, you must use 1-digit report codes.

Dialing Method

Section

[800]

: Dialer Options

Option

[6]

OFF= Pulse Dialing (see “Pulse Ratio” on page 41).

Option

[6]

ON= Tone/DTMF Dialing (default)

Pulse Ratio

Section

[800]

: Dialer Options

Option

[7]

OFF= European Pulse Ratio of 1:2

Option

[7]

ON= U.S.A. Pulse Ratio of 1:1.5 (default)

When using Pulse dialing, you can select one of two Pulse Ratios. Although most European countries use the 1:2 pulse ratio, the 1:1.5 ratio may provide better results
in some cases. The same applies for North American countries. If the 1:1.5 pulse ratio is not providing the desired results, the 1:2 ratio may be used.

Maximum Dialing Attempts

Section

[831]

000 to 255 attempts, Default = 8 attempts

The value programmed in section

[081]

determines how many times the control panel will re-dial the same monitoring station telephone number before

proceeding to the next number.

Maximum Dialing Attempts - VDMP3

Section

[841]

000 to 255 attempts, Default = 8 attempts

The value programmed in section

[841]

determines how many times the control panel will re-dial the same telephone number before proceeding to the next

number. The maximum dialing attempts programmed in this section is independent from those programmed in section

[831]

of the panel dialer used for

monitoring station reporting.

Delay Between Dialing Attempts

Section

[832]

000 to 255 seconds, Default = 20 seconds

This delay determines the amount of time the control panel will wait between each dialing attempt.

This section applies to the Plug-in Voice Dialer when using

a VDMP3.

Switch to Pulse on 5th Attempt

Section

[800]

Option

[3]

OFF=

Switch to Pulse on 5th Attempt Disabled (default)

Option

[3]

ON=

Switch to Pulse on 5th Attempt Enabled

With option

[3]

ON, the control panel will switch to pulse dialing on the 5th attempt of reaching the monitoring station.

Alternate Dial Option

Section

[800]

: Dialer Options

Option

[4]

OFF= Alternate Dial Disabled (default)

Option

[4]

ON= Alternate Dial Enabled

With option

[4]

OFF, the control panel will dial the backup programmed in section

[817]

after all attempts to one monitoring station number have failed. With

option

[4]

ON, the control panel will dial the backup number after every failed attempt.

Force Dial Option

Section

[800]

: Dialer Options

Option

[5]

OFF= Force Dial Disabled

Option

[5]

ON= Force Dial Enabled (default)

With option

[5]

is enabled, the panel will dial a telephone number even if no dial tone is present after 4 seconds.

«
...
39
40
41
42
43
...
»

Содержание MG5000+
























































Отзывы:

Нет отзывов

Похожие инструкции для MG5000+

Бренд: Jensen Страницы: 12

Бренд: Power Acoustik Страницы: 5

Бренд: Hercules Страницы: 6

Бренд: sewerin Страницы: 102

Бренд: Velleman Страницы: 22

Бренд: SpeakerCraft Страницы: 2

CIRCOtransfer 30 E

Бренд: wagner solar Страницы: 32

ClareOne CLR-C1-WTR

Бренд: clare Страницы: 2

Бренд: K-array Страницы: 52

PRO-9642a Pursuit Series

Бренд: Audiovox Страницы: 8

Бренд: WELTECH Страницы: 41

Бренд: Abus Страницы: 124

Бренд: Polaroid Страницы: 73

Бренд: Surveon Страницы: 59

Бренд: Miller Weldmaster Страницы: 20

Бренд: SEC Страницы: 6

Бренд: Abus Страницы: 48

Бренд: Marshall Electronics Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды