Paradise Datacom Quantum Скачать руководство пользователя страница 143 | Manualshive

Страница: 143 / 354

background image

Quantum and Evolution Series Installation and Operating Handbook

7-114

Brouting mode

Select this mode for all point-to-multipoint or unidirectional IP systems
where there is an indirect return path (i.e. not via satellite). Both the Tx and
Rx modems should have brouting enabled. In this mode, the Ethernet
bridge in the Tx modem does not expect to receive replies and simply
transmits all Ethernet frames over satellite other than those destined for
itself.

TCP acceleration mode

This mode provides bridging of non-TCP packets combined with
acceleration of TCP packets using a Performance Enhancing Proxy (PEP)
that overcomes performance problems associated with using standard TCP
over satellite.

TCP acceleration mode + Header Compression

Only applicable if an IP traffic Interface card is fitted. This mode provides
bridging of non-TCP packets, acceleration of TCP packets and header
compression.

TCP Acceleration

This mode supports point-to-multipoint TCP acceleration. The remote
modems should be set to this mode and VLAN filtering should also be
enabled.

Hub + TCP Acceleration

This mode supports point-to-multipoint TCP acceleration. The hub Tx
modem should be set to this mode and VLAN filtering should also be
enabled on this modem. Note that hub Rx-only modems in a point-to-
multipoint TCP acceleration system should be set to

Hub

mode (not

Hub +

TCP Acceleration

) and that the Rx-only modems should have VLAN filtering

disabled.

Factory
default:

Bridge mode

Description:

This allows selection of the mode of operation of the modem Ethernet
bridge. See Section 8.12 for further details of bridge operation.

«
...
141
142
143
144
145
...
»

Содержание Quantum



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Quantum

Бренд: PROLiNK Страницы: 10

Web n Walk Stick

Бренд: T-Mobile Страницы: 8

Zlinx Xtreme IP67 ZXT9-RM

Бренд: B&B Electronics Страницы: 164

Бренд: OUMAN Страницы: 8

Touchstone TM608

Бренд: Arris Страницы: 32

Бренд: Farallon Страницы: 162

Бренд: TP-Link Страницы: 24

Бренд: Zoom Страницы: 2

Бренд: Zoom Страницы: 32

Бренд: Zoom Страницы: 33

Бренд: Eaton Страницы: 2

Бренд: 3Com Страницы: 12

U.S. Robotics 56K Professional Message

Бренд: 3Com Страницы: 37

Бренд: Hughes Страницы: 61

Бренд: Embedded Страницы: 44

Бренд: Radio Shack Страницы: 8

Бренд: Zte Страницы: 6

Бренд: Zte Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды