manualshive.com logo in svg

Paradise Datacom Quantum, Инструкция по установке и эксплуатации

Поделиться
Скачать
Paradise Datacom Quantum Скачать руководство пользователя страница 113

Quantum and Evolution Series Installation and Operating Handbook 

 

 

 7-84

 

This menu contains the following options: 
 

•

 

Service

. This option allows the selection of the framing mode for the modem. 

•

 

Baseband

.

 

This option leads to a submenu that allows terrestrial framing, timeslots 

and overhead to be configured. 

•

 

Clocks

. This allows the receive path clock to be set up. 

•

 

Demodulate. 

This leads to a submenu that allows the demodulation scheme to be 

configured. 

•

 

FEC. 

This leads to a submenu that contains options for selecting the inner and outer 

forward error correction (FEC) schemes. 

•

 

Descrambler. 

This leads to a submenu that allows descrambling to be controlled. 

•

 

Carrier.

 This leads to a submenu that allows the frequency and spectrum inversion to 

be controlled. 

•

 

Rx=Tx.

 This option allows the receive path to be automatically configured to be the 

same as the transmit path, thereby simplifying set up. There are a number of 
exceptions including carrier frequency, spectral inversion, timeslots and clocks. 

•

 

Interface.

 This submenu is used to configure the Rx path of the Quad E1 interface 

card. 

 
 

7.3.3.2.1 Edit-Rx-Service Screen 

 

See the description of the transmit path equivalent. 
 

Edit-Rx-Service- IDR Frame Format Screen 

 
See the description of the transmit path equivalent. 
 

7.3.3.2.2 Edit-Rx-Baseband Menu 

See the description of the transmit path equivalent. 
 

Edit-Rx-Baseband Mode Screen 

See the description of the transmit path equivalent. 
 

1:Service          2:Baseband   3:Clocks       
4:Demodulate  5:FEC             6:Descrambler  
7:Carrier           8:Rx=Tx         9:Interface

 

Содержание Quantum



































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды