Pandora Elite v2, Руководство пользователя

Страница: 23 / 27

45
44
U S E R MA N UA L PA N D O R A E L I T E V2
CONTROL OF THE SYSTEM IN CASE OF EMERGENCY
The system has emergency ways to deactivate security and anti-hi-jack functions (using the VALET
button and the “Secret PIN-code”) in case of loss or failure of control devices or in case of discharge of a
battery (when you cannot replace it or charge).
Before using emergency system control, check the system and vehicle control devices: check a
battery, turn on a device in accordance with its manual (if required).
If all devices are working, try to make a primary vehicle diagnosis: check the vehicle original control
device, vehicle battery charge level, gearbox selector position, check information on the dashboard.
!
t
he system cAN be coNtRolled fRom A phoNe usING
dtmf
commANds
0* – d
IsARmING
.
998*
xxxх
– d
eActIvAte AuthoRIzAtIoN devIces
(I
mmobIlIzeR ANd
A
NtI
-h
IjAck fuNctIoNs
),
WheRe хххх Is the
“s
ecRet
pIN-
code
”
WRItteN oN the
o
WNeR
’
s peRsoNAl cARd uNdeR the pRotectIve lAyeR
.
1*– A
RmING
.
888* – A
ctIvAte AuthoRIzAtIoN devIces
(I
mmobIlIzeR ANd
A
NtI
-h
IjAck fuNctIoNs
).
!
R
eAd the pRoceduRe foR eNteRING the
pIN-
code befoRe usING emeRGeNcy fuNctIoNs
.
ENTERING THE PIN-CODE
The code must be entered only when the base unit is powered and the ignition is off. The PIN-code
can be entered using the external or located on the base unit VALET button. The digits input and correct
input is indicated by the external or located on the base unit LED indicator.
• Enter the first digit • Press the button the number of times equal to the first digit. Pauses between
presses should not exceed 1 second. Each pressing will be confirmed with an orange LED indicator
flash. Pause for more than 1 second, a red LED indicator flash and a short sound single of the Beeper
confirm the input of the first digit. Then you can enter the next digit.
• Enter the second digit • Press the button the number of times equal to the second digit. Pauses
between presses should not exceed 1 second. Each pressing will be confirmed with an orange LED
indicator flash. Pause for more than 1 second, a red LED indicator flash and a short sound single of
the Beeper confirm the input of the second digit. Then you can enter the next digit.
• Enter the third digit • Press the button the number of times equal to the third digit. Pauses between
presses should not exceed 1 second. Each pressing will be confirmed with an orange LED indicator
flash. Pause for more than 1 second, a red LED indicator flash and a short sound single of the Beeper
confirm the input of the third digit. Then you can enter the next digit.
• Enter the fourth digit • Press the button the number of times equal to the fourth digit. Pauses
between presses should not exceed 1 second. Each pressing will be confirmed with an orange LED
indicator flash. The correct input will be confirmed with the series of green and red flashes of the
LED indicator.
Emergency disarming
In case you cannot disarm the system as usual, use the VALET button and the ‘Secret PIN-code’ written
on the Owner’s personal card (see the “General information” section):
• If your car is locked, unlock it by an original key. Not paying attention to the siren signals, make sure
that the ignition is off and enter the “Secret PIN-code” (see the procedure description above). If there
are no siren sounds or LED flashes, check the battery. It is not possible to enter the “Secret PIN-code”,
if there is no power supply.
• The system will be disarmed in case of correct PIN-code input. It will be confirmed with the series of
green and red flashes of the LED indicator, the series of sound signals of the Beeper, 4 beeps of the
Siren and 4 signals of the light signalization.
• The system will stay in previous state in case of incorrect input of the PIN-code. It will be indicated
with a long red flash of the LED indicator. New input can be attempted after 5 seconds.
• Emergency disarming is equivalent to a normal method of disarming. No additional actions are
required for further operation of the system.
Emergency control of the anti-theft functions
This section describes how to deactivate and activate anti-theft functions (Immobilizer and Anti-Hi-
jack), which use a radio tag, a remote control or a mobile phone as an owner authorization device,
and “Code immobilizer” function, which uses standard car controls (buttons, levers, pedals) to enter the
Immobilizer PIN-code.
Emergency deactivation of anti-theft functions
To temporarily deactivate the Immobilizer or Code immobilizer function (pin-to-drive), turn on the
ignition when the system is disarmed. Enter the “Secret code” from the owner’s personal card using the
VALE T butt on. The immobilizer functions will be being deactivated by the time the ignition is turned off.
Emergency activation/deactivation Immobilizer/Code Immobilizer functions
Emergency control of the anti-theft functions is possible only when the system is disarmed, the
ignition is off, service mode is deactivated, a vehicle battery is charged.
Enter the “Secret PIN-code” or the “Service PIN-code” (default value is 1-1-1-1) to put the system in
programming mode.