Panasonic WV-SW390 Series Скачать руководство пользователя страница 125

Страница: 125 / 224

Note

•

The other i-PRO series products do not support “G.711” unless otherwise stated. (As of August, 2011)

•

G.711 is available only when “Mic input” is selected for “Audio transmission/reception”.

[Audio bit rate]

Select “16kbps” or “32kbps” for the audio bit rate used to transmit/receive audio data.

•

Default:

32kbps

Note

•

When selecting a smaller value for “Bandwidth control(bit rate)” (

page 160) while putting a priority

on the JPEG/H.264(MPEG-4) image transmission, select “16kbps” for “Audio bit rate”.

•

[Audio bit rate] is unavailable when “G.711” is selected for “Audio encoding format”.

[Mic input volume (Camera to PC)]

Select a volume level on the PC to hear audio transmitted from the camera.

•

Mic High:

The volume level will become high. This setting will be applied when audio is input to the camera

using a microphone.

•

Mic Middle:

The volume level will become middle. This setting will be applied when audio is input to the

camera using a microphone.

•

Mic Low:

The volume level will become low. This setting will be applied when audio is input to the camera

using a microphone.

•

Line High:

The volume level will become high. This setting will be applied when audio is input to the camera

using the Line input.

•

Line Middle:

The volume level will become middle. This setting will be applied when audio is input to the

camera using the Line input.

•

Line Low:

The volume level will become low. This setting will be applied when audio is input to the camera

using the Line input.

•

Default:

Mic Middle

[Mic input interval (Camera to PC)]

Select an interval for audio reception from the following.
20ms/ 40ms/ 80ms/ 160ms

•

Default:

40ms

Note

•

When a shorter interval is selected, the delay time will be shorter. When a longer interval is selected,
audio interruption may be diminished even though the delay time will be longer. Select the interval
according to the network environment.

[Audio output volume (PC to Camera)]

Select a volume level on the camera to hear audio transmitted from the PC.
High/ Middle/ Low

•

Default:

Middle

[Audio output interval (PC to Camera)]

Select an interval for audio transmission from the following.
160ms/ 320ms/ 640ms/ 1280ms

•

Default:

640ms

Note

•

Operating Instructions

125

11 Configure the settings relating to images and audio [Image/Audio]

Содержание WV-SW390 Series

































































































































































































































Результаты поиска

Содержание WV-SW390 Series

Отзывы:

Похожие инструкции для WV-SW390 Series

Бренды по названию

Популярные бренды

Panasonic WV-SW390 Series, Руководство по эксплуатации

Результаты поиска

Содержание WV-SW390 Series

Отзывы:

Похожие инструкции для WV-SW390 Series

Бренды по названию

Популярные бренды