Panasonic WH-SDC12F6E5 Скачать руководство пользователя страница 100 | Manualshive

Страница: 100 / 179

background image

100

15. Servicing

Guide

15.1 How to Take Out Front Plate

Please follow the steps below for take out front plate. Before removing the front plate of indoor unit, always switch off
all power supply (i.e. indoor unit power supply, heater power supply and tank unit power supply).

1 Remove the 2 mounting screws which located at bottom of the front plate and 1 mounting screw at the front

of the plate.

2 Gently pull the lower section of the front plate towards you to remove the front plate from left and right hooks.
3 Hold the left edge and right edge of front plate to lift up front plate from hooks.

When reinstalling the

front plate, first set the

2 hooks, which located

at the top of front plate,

into the slots at cabinet.

Then carry out above

steps in the reverse

order.





Hook

Lift up

Screws

Fix the left and right hooks to cabinet
slot properly when reinstall front plate.

15.2 How to Take Out Side Cabinet

Please follow the steps below to remove the side
cabinet. Before removing the front plate of indoor unit
always switch off all power supply (i.e. indoor power
supply, heater power supply and tank unit power
supply).

1 Perform the steps in HOW TO TAKE OUT

FRONT PLATE.

2 Remove all the 13 mounting screws on the left,

right and top of the side cabinet.

3 Gently remove the side cabinet by holding both

of the handles.

15.3 Test

Run

1 Fill up the boiler tank with water. For details refer to boiler tanks installation instruction and operation

instruction.

2 Set ON to the indoor unit and RCCB/ELCB. Then, for control panel’s operation please refers to air-to-water

heatpump’s operation instruction.

3 For normal operation, pressure gauge reading should be in between 0.05 MPa and 0.3 MPa.

If necessary, adjust the water pump speed accordingly to obtain normal water pressure operating range. If
adjust water pump speed cannot solve the problem, contact your local authorized dealer.

4 After test run, please clean the external filter. Reinstall it after finish cleaning.

15.4 Proper Pump Down Procedure [SERVICE MODE: 01]

WARNING

Strictly follow the steps below for proper pump down procedure. Explosion may occur if the steps are not followed as per
sequence.

1

When the heatpump unit is not in operation (standby), press the “SERVICE” switch on control panel to enter SERVICE
mode. Operate the system in Sr : 01 mode for pump down operation.

2

After 10 ~ 15 minutes, (after 1 or 2 minutes in case very low ambient temperatures (< 10°C)), fully close 2 way valve.

3

After 3 minutes, fully close 3 way valve.

4

Press the “OFF/ON” switch on control panel to stop pump down operation.

5

Remove the refrigerant piping.

«
...
98
99
100
101
102
...
»

Содержание WH-SDC12F6E5




















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WH-SDC12F6E5

Бренд: Gabarron Страницы: 8

Бренд: Larzep Страницы: 14

DONYER POWER CH-1500

Бренд: Intertek Страницы: 12

Racor RK15438-01

Бренд: Parker Страницы: 8

Бренд: Dura Heat Страницы: 22

Бренд: Hyco Страницы: 12

DRENAG 1000-1200

Бренд: Saci Страницы: 134

Бренд: Envision Страницы: 47

Бренд: Bard Страницы: 27

Бренд: Costa Страницы: 12

Бренд: Elite Страницы: 9

Бренд: Sears Страницы: 9

Altherma 3 H F+W EABH16DF9W

Бренд: Daikin Страницы: 60

Бренд: SAMES KREMLIN Страницы: 49

Бренд: STIEBEL ELTRON Страницы: 96

Eyecatchers Iguana Aplano

Бренд: Jaga Страницы: 2

Бренд: ABS Страницы: 10

Бренд: NAVAC Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды