Panasonic WH-MDF12C6E5 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 121

background image

50

12.1.5 Setting Water Outlet Temperature for Heat Mode

The set temperature define the parameters for the outdoor ambient temperature dependent operation of the unit.

Where by the internal water setting temperature is determined automatically depending on the outdoor
temperature. The colder outdoor temperatures will result in warmer water and vice versa. The user has the
possibility to shift up or down the target water temperature by remote control setting.

Change in setting water outlet temperature is updated every 30 minutes.

12.1.5.1 Heating

Mode

Operation Time Chart

Operation of heat pump provide heating capacity to room side by hot water through heating panel, floor or fan

coil.

1 3 ways valve control:

o

3 ways valve switch and fix to heating side.

2  Heat pump operate follow normal heating operation.
3  Backup heater operate follow normal operation.
4  Solar 3 way valve operates follow solar operation specification.
5  2 way valve opens.

12.1.6 Water Temperature Thermo Shift Setting

  Switchs are ignored during “PUMPDW” = ON.
  Switchs are ignored during “STATUS” = ON.
  “

▲

”, “

▼

”, “SELECT” switch are ignored if “SETTING” = OFF.

  “CANCEL” switch is ignored if “SETTING” = OFF & “STATUS” = OFF.
  If “SET” Switch pressed for less than 5secs, immediately enter water temperature shift setting mode.
  Once enter this setting mode, “SETTING” display is ON.

This setting mode is used to easily shift the target water outlet temperature.

«
...
48
49
50
51
52
...
»

Содержание WH-MDF12C6E5


























































































































Отзывы:

Нет отзывов

Похожие инструкции для WH-MDF12C6E5

Бренд: iBath Страницы: 12

Бренд: EarthLinked Страницы: 6

Бренд: Oceanic Страницы: 201

WFC-03 HCM RF 230

Бренд: Watts Страницы: 11

UNI_SAUNA_B4.5KW

Бренд: UNIPRODO Страницы: 17

Comfortstat 2 F 8ST

Бренд: GDC Страницы: 28

SkyAir RZR-P Series

Бренд: Daikin Страницы: 202

Бренд: T.I.P. Страницы: 133

FLOWMAX PU 2125 F

Бренд: SAMES KREMLIN Страницы: 32

Бренд: Uni-max Страницы: 6

Бренд: Calorex Страницы: 156

POOLEX JETLINE SELECTION FI

Бренд: poolstar Страницы: 7

Бренд: Sonnenkonig Страницы: 48

Бренд: Olimpia splendid Страницы: 36

Бренд: WarmPool Страницы: 30

SOLANO INDUSTRY-W-150

Бренд: Cairox Страницы: 10

Бренд: Easy@Home Страницы: 20

Emotion barres Digital

Бренд: Thermor Страницы: 51

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды