Panasonic WH-MDF12C6E5 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 121

background image

52

12.3 Pump Down Operation

Purpose

Ensure the pump down operation when relocating or disposing of the unit. The pump down operation will extract all
refrigerant from the piping into the mono bloc unit.

Pump down operation control:

1  Press the SERVICE S/W for continuous 5 secs to enter Service mode.
2  In service mode, select Sr:01 and press SET S/W to start Pump Down operation.
3  There will be no Low Pressure error & Freeze prevention judgement during pumpdown operation.
4  3 ways valve will shift to room side.
5  Press the ON/OFF button to stop the unit.

12.4 Flow

Switch

12.4.1 Flow Switch Control

1 The water flow switch serve as an overload protector that shuts down the unit when the water level is

detected to be low.

2 Detection is Lo (0V) when there is no water flow, and detection is Hi (5V) when there is water flow.

12.5 Force Heater Mode Operation

The backup heater also serves as backup in case of malfunctioning of the mono bloc unit.

1  Make sure the OFF/ON remote control LED is OFF (no operation).
2  Press the Force button to start the force heater mode operation.
3  During force heater mode, all other operations are not allowed.
4  Press OFF/ON button to stop the force heater mode operation.

«
...
50
51
52
53
54
...
»

Содержание WH-MDF12C6E5


























































































































Отзывы:

Нет отзывов

Похожие инструкции для WH-MDF12C6E5

Бренд: Eaton Страницы: 12

Бренд: TABLE HEATERS Страницы: 27

Бренд: Rasonic Страницы: 8

Бренд: WACKER Group Страницы: 60

PROFESSIONAL 5965-01

Бренд: Simer Страницы: 19

Бренд: Bard Страницы: 26

Бренд: Vagner Pool Страницы: 35

Бренд: DAB Страницы: 72

Бренд: nedis Страницы: 60

EASYDOS Peristaltic V

Бренд: Jesco Страницы: 20

Бренд: Sanden Страницы: 48

BlackFin CT-2902BPHP

Бренд: Panduit Страницы: 68

Бренд: OmarLift Страницы: 28

Oberdorfer 800B

Бренд: Gardner Denver Страницы: 2

Бренд: Olimpia splendid Страницы: 52

Бренд: ElectrIQ Страницы: 24

Бренд: UNITED Страницы: 9

EUROSTOVE SRE 301 -

Бренд: Eurostove Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды