Panasonic S-15MF3E5AN Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 66

Panasonic S-15MF3E5AN Скачать руководство пользователя страница 64

64

●

Check Before Requiring Services

Symptom

Cause

Remedy

Air conditioner does not run at
all although power is turned
on.

Power failure or after power failure

Press ON/OFF operation button on remote
controller again.

Operation button is turned off.

●

Switch on power if breaker is turned off.

●

If breaker has been tripped, consult your dealer

without turning it on.

Fuse blow out.

If blown out, consult your dealer.

Poor cooling or heating
performance

Air intake or air discharge port of indoor
and outdoor units is clogged with dust or
obstacles.

Remove dust or obstruction.

Fan speed switch is set to “Low”.*

Change to “Medium” or “High”.*

Improper temperature settings

See Section “

■

Tips for Energy Saving”.

Room is exposed to direct sunlight in
cooling mode.

Doors and /or windows are open.

Air filter is clogged.

See Section “

■

Care and Cleaning”.

Too much heat sources in room in
cooling mode.

Use minimum heat sources and in a short time.

Too many people in room in cooling
mode.

Reduce temperature settings or change to “Medium”
or “High”.*

* Fan speed display on the remote controller

High :

(CZ-RTC4),

(CZ-RTC5B, CZ-RTC6 series)

Medium :

(CZ-RTC4),

(CZ-RTC5B, CZ-RTC6 series)

Low :

(CZ-RTC4),

(CZ-RTC5B, CZ-RTC6 series)

If your air conditioner still does not work properly although you checked the points as described
above, first stop the operation and turn off the power switch. Then contact your dealer and
report the serial number and symptom. Never repair your air conditioner by yourself since it is
very dangerous for you to do so. You also report if the inspection mark and the letters E, F, H, J,
L, P in combination with the numbers appear on the LCD of the remote controller.

01_350221_Eng.indb 64

2023/3/17 10:01:21

«
...
62
63
64
65
66
»

Содержание S-15MF3E5AN



































































Отзывы:

Нет отзывов