manualshive.com logo in svg

Panasonic S-15MF3E5AN, Руководство по установке, Страница: 62 / 66

Поделиться
Скачать
Panasonic S-15MF3E5AN Скачать руководство пользователя страница 62

62

 CAUTION

●

  Certain metal edges and the condenser fins are sharp and may cause injury if handled 

improperly; special care should be taken when you clean these parts.

●

  Periodically check the outdoor unit to see if the air outlet or air intake is clogged with 

dirt or soot.

●

  The internal coil and other components must also be cleaned periodically. Consult 

your dealer or service center.

Care: After a prolonged idle period

Check the indoor and outdoor unit air intakes and outlets for blockage; if there is a blockage, 
remove it.

Care: Before a prolonged idle period

●

  Operate the fan for half a day to dry out the inside.

●

  Disconnect the power supply and also turn off the circuit breaker. 

●

  Clean the air filter and replace it in its original position.

●

  Outdoor unit internal components must be checked and cleaned periodically. Contact your 

local dealer for this service.

01_350221_Eng.indb   62

2023/3/17   10:01:20

Содержание S-15MF3E5AN



































































Отзывы:

Нет отзывов