Panasonic S-15MF3E5AN Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 66

Panasonic S-15MF3E5AN Скачать руководство пользователя страница 47

47

Change the display from “OFF” to “ON” by pressing the

or

button.

Then press the

button.

The “Maintenance func” screen appears on the LCD
display.

9. Press the

button. “TEST” will be displayed on the

LCD display.

10. Press the

button. Test run will be started.

Test run setting mode screen appears on the LCD display.

11. Set the operation mode to “

(MODE FAN)” and fan

speed mode to “

(FAN SPEED)” by pressing the

or

button or

or

button.

Then press the

button.

The fan motor will be activated, the auto external static
pressure setting operation and setting-check operation will
be performed for about 3 to 30 minutes.
The fan speed will change automatically while these
operations are in progress. When these operations
completed, “TEST” will be disappeared from the LCD
display.

[

] Confirm

Test run

Change

20:30 (THU)

Test run

ON

Maintenance func

1. Outdoor unit error data
2. Service contact
3. RC setting mode

Sel.

Page [

] Confirm

20:30 (THU)

4. Test run

START

[

]

20:30 (THU)

TEST

FAN SPEED

FLAP

TEST

20:30 (THU)

COOL

MODE

FAN SPEED

FLAP

TEST

20:30 (THU)

MODE

FAN

FAN SPEED

FLAP

20:30 (THU)

MODE

FAN

20:30 (THU)

START

[

]

NOTE:

The auto external static pressure setting operation and setting-check operation will not be

performed unless “

(MODE FAN)” and “

(FAN SPEED)” have been selected.

12. Press the

button.

The LCD display will be returned to the initial screen.

NOTE:

Failure to set this parameter may result in decreased airflow and condensation.

01_350221_Eng.indb 47

2023/3/17 10:01:16

«
...
45
46
47
48
49
...
»

Содержание S-15MF3E5AN



































































Отзывы:

Нет отзывов