Panasonic S-15MF3E5AN Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 66

Panasonic S-15MF3E5AN Скачать руководство пользователя страница 49

49

10-3-2. Auto Airflow Volume Control Operations and External Static Pressure Setting-

Check Operation

1. Press and hold down the

button for 4 or more

seconds. “

” will be displayed on the LCD

display.

2. Press the

button to start the test run.

3. Select the operation mode

(Fan) by pressing the

A

(Mode select) button.

Then select the fan speed

by pressing the

(Fan speed) button.

N OT E

Auto airflow volume control operations and
external static pressure setting-check operations
will not be performed unless the above settings
are made.

4. The fan motor will be activated and auto airflow volume control operations or external static

pressure setting-check operations will be started.

The power of the airflow will change while these operations are in progress.

The external static pressure setting-check operations and auto airflow volume control

operations will be completed in about 3 to 30 minutes.

“ ” display will be disappeared from the LCD display.

5. Press the

button to halt the test run.

A

°

°

1

3

2, 5

01_350221_Eng.indb 49

2023/3/17 10:01:18

«
...
47
48
49
50
51
...
»

Содержание S-15MF3E5AN



































































Отзывы:

Нет отзывов