Panasonic S-15MF3E5AN Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 66

Panasonic S-15MF3E5AN Скачать руководство пользователя страница 15

15

3-3. Fix the Indoor Unit

3-3-1. Horizontal Installation

Depending on the ceiling type:

a) Insert suspension bolts.

or

b) Use existing ceiling supports or construct a suitable support.

Insert

Hole-in-anchor
Hole-in-plug

Concrete

Suspension bolt (M10 or 3/8”)
(field supply)

a)

b)

Ceiling support

Ceiling tiles

WARNING

It is important that you use extreme care in supporting the indoor unit inside the ceiling.
Ensure that the ceiling is strong enough to support the weight of the unit. Before
hanging the unit, test the strength of each attached suspension bolt.

(1) When placing the unit inside the ceiling, determine the pitch of the suspension bolts

referring to the dimensional data as shown in the tables and diagrams under Section 3-1.
Tubing must be laid and connected inside the ceiling when suspending the unit. If the
ceiling is already constructed, lay the tubing into position for connection to the unit before
placing the unit inside the ceiling.

(2) Screw in the suspension bolts allowing them to protrude from the ceiling. (Cut the ceiling

material, if necessary.)

(3) Thread the 3 hexagonal nuts and 2 washers (field supply) onto each of the 4 suspension bolts.

Use 1 nut and 1 washer for the upper part, and 2 nuts and 1 washer for the lower part, so that
the unit will not fall off the suspension lugs.

Nuts and washers
(use for upper and lower)

Suspension lug

Double nuts

Suspension bolt

Notch

Suspension bolt

Double nuts

Hexagonal nut

01_350221_Eng.indb 15

2023/3/17 10:01:05

«
...
13
14
15
16
17
...
»

Содержание S-15MF3E5AN



































































Отзывы:

Нет отзывов