manualshive.com logo in svg

Panasonic S-15MF3E5AN, Руководство по установке, Страница: 13 / 66

Поделиться
Скачать
Panasonic S-15MF3E5AN Скачать руководство пользователя страница 13

13

3-2. Preparation Before Installation

3-2-1. Main Types of Installation

Case A 

(Standard installation)

Horizontal installation in the ceiling, 
rear side air intake

Rear side air intake

Case C

Vertical installation on the sidewall, lower 
side air intake

Lower side air intake

*  While in heating mode, the temperatures 

may increase higher than the set 
temperature.

Case B

Horizontal installation in the ceiling, lower 
side air intake

Lower side air intake

Case D

Vertical installation on the sidewall, front side 
air intake

Front side air intake

*  While in heating mode, the temperatures 

may increase higher than the set 
temperature.

3-2-2. Install the Filter

When not connecting the air intake duct, be sure to install the filters (Accessories).
Case A and Case C are shown below.

Filter (Accessory)

Screw

A

Type 15, 22, 28, 36, 45, 56

Filters (Accessories)

Screws

A

Type 60, 73, 90, 106, 112, 140, 160

View A

Main unit

Filter

Attach the filter to the main unit while 
pushing the tip of the latches in the 
direction of the arrow.

Attach the filters (accessories) in the manner shown in the figure.
Securely fix the filters with the screws.

01_350221_Eng.indb   13

2023/3/17   10:01:03

Содержание S-15MF3E5AN



































































Отзывы:

Нет отзывов