Panasonic PT-SRQ35KC, Руководство по эксплуатации

Страница: 299 / 323

Chapter 7 Appendix
—
Technical information
EN G L ISH - 2 99
Control command
The follo w ing table lists the co mm ands that can be used to control the projector using a co m puter.
r
Projector control command
Command Details
Parameter/response
string
Remark (parameter)
PO N Po w er on
— To check if the po w er is on, use the “Po w er query ” co mm and.
POF Po w er standby
QPW Po w er query
000
001
ST AN DBY
Po w er on
IIS
S w itching the input
signal
HD 1 HDMI
D L1 DIGIT AL L I N K
AU1 ,SD 1
* 1
SDI 1 [S L OT 1 ]
AU1 ,SD 2
* 1
SDI 2 [S L OT 1 ]
AU1 ,SD 3
* 1
SDI 3 [S L OT 1 ]
AU1 ,SD 4
* 1
SDI 4 [S L OT 1 ]
AU2 ,SD 1
* 2
SDI 1 [S L OT 2 ]
AU2 ,SD 2
* 2
SDI 2 [S L OT 2 ]
AU2 ,SD 3
* 2
SDI 3 [S L OT 2 ]
AU2 ,SD 4
* 2
SDI 4 [S L OT 2 ]
AU1 ,HD 1
* 3
HDMI 1 [S L OT 1 ]
AU1 ,HD 2
* 3
HDMI 2 [S L OT 1 ]
AU2 ,HD 3
* 4
HDMI 3 [S L OT 2 ]
AU2 ,HD 4
* 4
HDMI 4 [S L OT 2 ]
AU1 ,D V1
* 3
D V I-D 1 [S L OT 1 ]
AU1 ,D V2
* 3
D V I-D 2 [S L OT 1 ]
AU2 ,D V3
* 4
D V I-D 3 [S L OT 2 ]
AU2 ,D V4
* 4
D V I-D 4 [S L OT 2 ]
AU1 ,DP 1
* 3
DisplayPort 1 [S L OT 1 ]
AU1 ,DP 2
* 3
DisplayPort 2 [S L OT 1 ]
AU2 ,DP 3
* 4
DisplayPort 3 [S L OT 2 ]
AU2 ,DP 4
* 4
DisplayPort 4 [S L OT 2 ]
AU1 ,OP 1
* 3
SDI OPT 1 [S L OT 1 ]
AU1 ,OP 2
* 3
SDI OPT 2 [S L OT 1 ]
AU2 ,OP 1
* 4
SDI OPT 1 [S L OT 2 ]
AU2 ,OP 2
* 4
SDI OPT 2 [S L OT 2 ]
OSH Shutter control 0 Opened
QSH Shutter status query 1 C losed
V S E A spect ratio s w itch
0 D E F AUL T
1 4:3
2 1 6 : 9
5 THRO U GH
QS E
A spect ratio settings
query
6 H V FIT
9 H FIT
10 V FIT
O C S Sub m e m ory s w itch
01 - 96 Sub m e m ory nu m ber
QSB
Sub m e m ory status
query
* 1 This can be used w hen the optional Interface Board for 12 G-SDI ( Model N o. : E T-MD N12 G 10C) is installed in <S L OT 1 >.
* 2 This can be used w hen the optional Interface Board for 12 G-SDI ( Model N o. : E T-MD N12 G 10C) is installed in <S L OT 2 >.
* 3 This can be used w hen the optional Interface Board equipped w ith corresponding input is installed in <S L OT 1 >.
* 4 This can be used w hen the optional Interface Board equipped w ith corresponding input is installed in <S L OT 2 >.
r
Lens control command
Command Sub command Details Remark
VXX LN SI 2 L ens H shift
+ 00000 = Fine adjust m ent 1 +, + 00001 = Fine adjust m ent 1 -, + 00100
= Fine adjust m ent 2 +, + 00101 = Fine adjust m ent 2 -, + 00200 = C oarse
adjust m ent+, + 00201 = C oarse adjust m ent-
VXX LN SI 3 L ens V shift
VXX LN SI 4 L ens focus
VXX LN SI5 L ens zoo m