Panasonic PN28160A Скачать руководство пользователя страница 252

Страница: 252 / 277

252

Indicates that port initialization has failed due to hardware error.

Port-X link-down

Indicates that Port X was linked down.

Port-X link-up

info

Indicates that Port X was linked up.

SNMP

Not authorized!(IP: IP ADDRESS)

Indicates that an unauthorized IP address has accessed SNMP.

System authentication failure.

info

Indicates that SNMP authentication has failed.

SNTP

sendto: No route to host

Indicates that communication has failed due to no transmission route to configured
SNTP server.

recvfrom: Operation timed out

err

Indicates that time-out occurred in time synchronization with SNTP server.

SNTP first update to 2010/05/31 18:15:11

Indicates the initial time of synchronization with SNTP server after booting the
Switching Hub.

SNTP update to YYYY/MM/DD HH:MM:SS.

info

Indicates the time synchronized with SNTP server.

SYSTEM

System exception in thread:THREAD freeMem:FREE_MEM!

emerg

System information indicating that exception handler is called in the Switching
Hub. THREAD indicates the thread name, and FREE_MEM indicates the free
memory capacity.

Cannot open running-config file running_config!

Indicates that access to "running_config" file has failed.

Cannot save to configuration file, file not found!

Indicates that saving of configuration file has failed because the file was not
found.

TFTP module initialization failed!

Indicates that TFTP execution has failed due to system error.

Cannot execute Ping by system error!

err

Indicates that Ping execution has failed due to system error.

Duplication of IP address IP ADDRESS (MAC ADDRESS).

Indicates that IP address of the Switching Hub is already used and conflicting.

Write configuration to primary file failed

warn

Indicates that saving of the configuration has failed.

Содержание PN28160A






















































































































































































































































































Результаты поиска

Содержание PN28160A

Отзывы:

Бренды по названию

Популярные бренды

Panasonic PN28160A, Руководство по эксплуатации

Результаты поиска

Содержание PN28160A

Отзывы:

Бренды по названию

Популярные бренды