Panasonic NR-B30FW1 Скачать руководство пользователя страница 40

Страница: 40 / 67

b. Pull Bag Joint from storage part of depths of

upper side of FC.
Cut Cable Tie of Bag Joint, then take Bag Joint.

c. Remove the connector of Temperature Fuse A’ssy,

then replace new Temp Fuse A’ssy.

NOTES ON INSTALLATION

•

Tighten Temp Fuse A’ssy by Cable Tie to pipe of Evapo-
rator.

•

Tighten Bag Joint that is put in the connector of Temp
Fuse A’ssy with other connectors by Cable Tie as
before.

•

Store Bag Joint to the place as before.

3. DEFROST HEATER A’SSY

a. Remove Defrost Heater A’ssy forward from right

and left side hooks that are fixation of Defrost
Heater A’ssy while pressing up hooks.

b. Remove Heater Cover of upper side of Defrost

Heater A’ssy.

c. Unhook 10 hooks, then remove the wires of

Defrost Heater A’ssy.

d. Pull Bag Joint from storage part of depths of

upper side of FC.
Cut Cable Tie of Bag Joint, then take Bag Joint.

e. Pull out two connectors of Radiant Heater A’ssy,

then replace new Defrost Heater A’ssy.

NOTES ON INSTALLATION

•

Install Heater Cover in rubber cap securely.

•

Arrange the lead wires, hook them to the wire hooks.

•

Tighten Bag Joint that is put in the connector of Defrost
Heater A’ssy with other connectors by Cable Tie as
before.

•

Store Bag Joint to the place as before.

NOTES ON INSTALLATION OF COVER COIL FC A’SSY

•

Install Cover Coil FC A’ssy in upper side of depths of
FC, then fix it by three screws.

•

It might be cause of getting frost, in case of imperfect
installation of Cover Coil FC A’ssy.

Содержание NR-B30FW1




































































Результаты поиска

Содержание NR-B30FW1

Отзывы:

Похожие инструкции для NR-B30FW1

Бренды по названию

Популярные бренды

Panasonic NR-B30FW1, Руководство по обслуживанию

Результаты поиска

Содержание NR-B30FW1

Отзывы:

Похожие инструкции для NR-B30FW1

Бренды по названию

Популярные бренды