Panasonic NR-B30FW1 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 67

background image

44

11.8. The Door Setting Exchange Work Manual

This appliance is setting right side opening door when it is shipped from the factory. However you can change the door
setting to left side opening to exchange those parts as below. You can exchange those parts to refer to the work manual
below.

TO PREPARE AND TO CONFIRM FOR THE WORK

1. Confirm the parts

Confirm whether there are those parts below or not.
(Bundled Parts)

(The matter of importance)

•

When you install an important hinge with the torque
restriction, tighten by a torque wrench after it fixes with
a plus screwdriver temporarily.

•

There is a possibility of damaging screw when strongly
tightening too much.

2. Remove trays and shelves of reverse side of Door

A’ssy PC.
Remove trays and shelves of reverse side of Door
A’ssy PC, to prevent the trays and shelves from
cracking and breaking. (When there is some foods
on reverse side of the door, it is necessary to take
foods out. When you do not take foods out, the floor
might be made dirty with the dropping foods.)

3. Unplug the refrigerator

Unplug the refrigerator before work for your safety.

NOTICE

• After the power is turned off, the temperature of each

compartments are risen.
There is turn ned off, the temperature of each compart-
ments are risen.

THE POINTS OF WORK

11.8.1. Remove Door A’ssy PC

1. 1. Remove Cover Hinge Top R

a. Insert screwdriver (-) to a gap of Button plate con-

trol, and pry it off.

b. Remove two screws that are fixation of Cover

Hinge Top R.

c. Pry off three Hooks (triangle mark part) of Cover

Hinge Top R by screwdriver (-), then remove
Cover Hinge Top R.

2. Remove Cover Table L.

• Remove Cover Table L in the same way above.

3. Remove Hinge Top R

a. Pull the connector from connector storage part,

then pull the connector out while pressing the
hook to upper side.

b. Remove three screws that are fixation of Hinge

Top R, pull the connector out through the hole of
Hinge Top R.

c. Remove three screws that are fixation of Hinge

Top L.

«
...
42
43
44
45
46
...
»

Содержание NR-B30FW1




































































Отзывы:

Нет отзывов

Похожие инструкции для NR-B30FW1

Бренд: GE Страницы: 1

Бренд: Thermador Страницы: 28

Бренд: Maytag Страницы: 40

Бренд: Waeco Страницы: 160

Бренд: Amana Страницы: 54

Бренд: Caloric Страницы: 24

Бренд: U-Line Страницы: 30

Бренд: Crosley Страницы: 2

Бренд: Rangemaster Страницы: 28

Бренд: Hanseatic Страницы: 74

Бренд: Saturn Страницы: 20

TBC-24-R/L-OG-A

Бренд: True Страницы: 60

Бренд: Danby DIPLOMAT Страницы: 24

Бренд: Electrolux Страницы: 2

Бренд: Electrolux Страницы: 3

Бренд: Electrolux Страницы: 13

Бренд: Electrolux Страницы: 13

Бренд: Electrolux Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды