Panasonic NR-B30FW1 Скачать руководство пользователя страница 35

Страница: 35 / 67

3. Check good operation or not those parts after the

work.

CAUTION

Be careful not to be bite the wires by Cover Sensor,
when store the wires and the Scotch Lock in Cover
Sensor.

11.2. Disassembly of VC (Vegetable

Compartment)

11.2.1. PCB (VC)

1. Remove Crisper A’ssy

• Pull Crisper Case, take it out from each two portions

of Rail VC right and left.
-You can see the figure below (11.2.2.(1)).

2. Remove the screw that is fixation of Cover LED on

upper side of VC. Then remove Cover LED.

3. (3)Remove PCB (VC) while pressing left and right

hooks of reverse side of Cover LED.

4. (4)Pull the connector out while pressing the hook.

NOTES

• Be careful not to break PCB (VC) when it is removed and

installed.

11.2.2. CRISPER A’SSY

1. Remove Crisper A’ssy.

• Pull Crisper Case, take it out from each two portions

of Rail VC right and left.

11.2.3. DUCT VC

1. Remove Crisper A’ssy

• Pull Crisper Case, take it out from each two portions

of Rail VC right and left.
-You can see the figure (11.2.2.(1)).

2. Remove Duct VC A’ssy towards you while pulling the

hook of upper side.

3. Remove Duct VC.

• Remove the connector of Damper Thermostat, then

take Duct VC out.

• Take out INS Duct VCT and INS Duct VCB from four

hooks of Duct VC.

• Tear off Foam tape, removes Sensor SC from fixation

part of INS Duct VCT.

Содержание NR-B30FW1




































































Результаты поиска

Содержание NR-B30FW1

Отзывы:

Похожие инструкции для NR-B30FW1

Бренды по названию

Популярные бренды

Panasonic NR-B30FW1, Руководство по обслуживанию

Результаты поиска

Содержание NR-B30FW1

Отзывы:

Похожие инструкции для NR-B30FW1

Бренды по названию

Популярные бренды