Panasonic NR-B30FW1 Скачать руководство пользователя страница 4

Страница: 4 / 67

Install and remove glass shelving securely to prevent risk of injury

When moving, raise the adjustable legs

Dragging the refrigerator will damage the floor. For flooring that may become easily damaged put a protective board in
place.

Do not scrape the metal rails

Take care of very hot parts

The compressor, pipes, etc. can be very hot during operation and directly after stopping. Also, the heater can be very hot
during power supply and immediately after power supply is stopped. Be careful not to burn yourself by touching very hot
parts.

Take care of very hot parts after welding

Pipes, etc., are very hot after welding. Be careful not to burn yourself by touching very hot parts.

Take care when filling/discharging refrigerant

Liquid refrigerant directly touching the skin may cause frostbite.

Take care of burrs

Be careful not to cut yourself on metal or plastic burrs.

Take care of condenser/evaporator fins

Be careful not to injure yourself on the fin edges.

Содержание NR-B30FW1




































































Результаты поиска

Содержание NR-B30FW1

Отзывы:

Похожие инструкции для NR-B30FW1

Бренды по названию

Популярные бренды

Panasonic NR-B30FW1, Руководство по обслуживанию

Результаты поиска

Содержание NR-B30FW1

Отзывы:

Похожие инструкции для NR-B30FW1

Бренды по названию

Популярные бренды