Panasonic NR-B30FW1 Скачать руководство пользователя страница 41

Страница: 41 / 67

11.4.4.

FAN MOTOR FC A’SSY

1. Take Case FCT A’ssy and Case FCB A’ssy out of FC.
2. Take Glass Tray FCT and Glass Tray FCB out.

a. Remove the screws that are fixation of Holder

Glass. (Each of two FC right and left)

b. Remove Holder Glass and pull Glass Tray FCT

and Glass Tray FCB out.

•

The figure is left side view also there are Holder Glass R
in the right side.

3. Take Cover Connector FC out

a. Remove the screw that is fixation of Cover Con-

nector FC on the left of upper side of FC.

b. Pull Cover Connector FC towards you, unhook the

Hooks (4 portions).

c. Remove sensor FC from the hook of reverse side

of Cover Connector FC, pull out the connector for
Fan Motor FC A’ssy.

4. Remove Cover Coil FC A’ssy

a. Remove three screws in front of Cover Coil FC

A’ssy.

b. Remove Cover Coil FC while pulling bottom side.

5. Take Fan Motor FC A’ssy out

a. Separate INS Cover Coil from two hooks of right

and left side of Coil Cover FC.

b. Take Fan Motor FC A’ssy out from INS Cover Coil

to press towards the arrow like the figure.

NOTES ON INSTALLATION

•

You can see the label of Fan Motor FC form this side

Содержание NR-B30FW1




































































Результаты поиска

Содержание NR-B30FW1

Отзывы:

Похожие инструкции для NR-B30FW1

Бренды по названию

Популярные бренды

Panasonic NR-B30FW1, Руководство по обслуживанию

Результаты поиска

Содержание NR-B30FW1

Отзывы:

Похожие инструкции для NR-B30FW1

Бренды по названию

Популярные бренды