Panasonic FP2 -C1A Скачать руководство пользователя страница 102

Страница: 102 / 121

FP2 Analog Unit

Troubleshooting

13 - 4

13.2 Problems Concerning the Analog Output

13.2 Problems Concerning the Analog Output

Problem

Remedy

Proper analog output cannot be

obtained.

Make sure that the FP2 CPU unit is in RUN mode.
Check the I/O allocation for the analog units.
Check the range settings.
Check the settings for no execution of conversion processing (shared

memory setting).
Make sure that the analog output data given to the analog unit is proper

for the range.
For current output, make sure that the impedance of the output load

device is 300

Ω

or less.

Check the analog signal wiring.

Analog output value is unsteady.

Make sure that you are using shielded twisted-pair wiring for the output

signal wires.
Make sure that the shielding of the shielded twisted-pair wiring is proper-

ly connected.
Make sure that no output signal wires are near other power wires.
Check the sequence program that gives the output data to the analog

unit.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Содержание FP2 -C1A


























































































































Результаты поиска

Содержание FP2 -C1A

Отзывы:

Похожие инструкции для FP2 -C1A

Бренды по названию

Популярные бренды

Panasonic FP2 -C1A, Руководство пользователя

Результаты поиска

Содержание FP2 -C1A

Отзывы:

Похожие инструкции для FP2 -C1A

Бренды по названию

Популярные бренды