Panasonic FP2 -C1A Скачать руководство пользователя страница 101

Страница: 101 / 121

FP2 Analog Unit

Troubleshooting

13 - 3

13.1 Problems Concerning the Analog Input

13.1 Problems Concerning the Analog Input

Problem

Remedy

Analog input conversion value cannot

be read.

Check the I/O allocation for the analog units.
Check the range settings.
Check the settings for no execution of conversion processing (shared

memory setting).
Check the analog signal wiring.

Proper current input conversion value

cannot be obtained.

Check the terminal block wiring.
Check the current input devices.

Conversion value is unsteady.

Make sure that you are using shielded twisted-pair wiring for the input

signal wires.
Make sure that the shielding of the shielded twisted-pair wiring is proper-

ly connected.
Make sure that no input signal wires are near other power wires.

Proper conversion value cannot be

obtained during R.T.D. Pt100

connection.

Check the range settings.
Check the three-wire wiring and restart the equipment.

Proper conversion value cannot be

obtained during thermocouple

connection.

Check the range settings.
Check the polarity of the thermocouple.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Содержание FP2 -C1A


























































































































Результаты поиска

Содержание FP2 -C1A

Отзывы:

Похожие инструкции для FP2 -C1A

Бренды по названию

Популярные бренды

Panasonic FP2 -C1A, Руководство пользователя

Результаты поиска

Содержание FP2 -C1A

Отзывы:

Похожие инструкции для FP2 -C1A

Бренды по названию

Популярные бренды