Panasonic FP2 -C1A Скачать руководство пользователя страница 119

Страница: 119 / 121

FP2 Analog Unit

Specifications

14 - 17

14.5 Shared Memory of Analog Output Processing

14.5 Shared Memory of Analog Output Processing

14.5.1

Analog Output Hold Setting (CPU unit with analog I/O: address 38)

(Analog output unit: address 17)

Sets either the non-hold, hold (final value during RUN mode), or hold (any value) for the

analog output during the FP2 CPU unit PROG. mode.

Address 38

Address 17

H0000: Non-hold

H0001: Hold (final value during RUN mode)

H0002: Hold (any value)
(Default: H0000)

Bit position

If a value different from those above is set, then non-hold is set.

14.5.2

Analog Output Hold (any value) Data Setting (CPU unit with

analog I/O: address 39) (Analog output unit: addresses 18 to 21)

As explained above, when a desired output is set for the hold setting, the analog output

value is held corresponding to the data set at this address.

15 14

Address 39

Addresses 18 to 21

10V output range: K-2048 to K2047

0 to 20mA output range: K0 to K4095

(Default: K0000)

Bit position

At the CPU unit with analog I/O

- address 39: analog output ch0

At the analog output unit

- address 18: analog output ch 0
- address 19: analog output ch 1
- address 20: analog output ch 2
- address 21: analog output ch 3

If a value different from those above is set, then the set value becomes disabled, and the

final output value before moving to the PROG. mode is held.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Содержание FP2 -C1A


























































































































Результаты поиска

Содержание FP2 -C1A

Отзывы:

Похожие инструкции для FP2 -C1A

Бренды по названию

Популярные бренды

Panasonic FP2 -C1A, Руководство пользователя

Результаты поиска

Содержание FP2 -C1A

Отзывы:

Похожие инструкции для FP2 -C1A

Бренды по названию

Популярные бренды