80
RQT9199
On the Unit’s Display
Page
H , F
(“ ” stands for a service number.)
An error has occurred. The number following “H” or “F” depends on the
status of the unit. Check the items below and in the Troubleshooting
Guide. If the service number still does not disappear after the check, reset
the unit ( 82, “To restore the unit if it freezes”).
−
If the service numbers fail to clear, note the service numbers and contact a
qualified service person.
−
DVD
(“ ” stands for a number.)
The remote control and the main unit are using different codes. Change
the code on the remote control.
82
HARD ERR
If there is no change after turning the unit on and off, consult the dealer
where the unit was purchased.
−
NoERAS
You cannot delete items on this disc.
The disc may be damaged. Use a new disc.
−
NoREAD
The disc is dirty or badly scratched. The unit cannot record, play, or edit.
77
The disc may be incompatible or of poor quality.
16, 17
You have used a lens cleaner and it has finished operation. Press
[
OPEN/CLOSE] on the main unit to eject the disc.
7
NoWRIT
You cannot write to this disc.
The disc may be damaged. Use a new disc.
−
FINAL
When the screen asking if you want to finalise the disc appears, the
message is displayed.
27
PLEASE WAIT
Displayed when the unit is started. This is not a malfunction.
−
The unit is carrying out its recovery process. You cannot operate the unit
while the message is displayed.
−
PROG FULL
There are already 32 timer recording programmes. Delete unnecessary
timer recording programmes.
32
REMOVE
The USB device is drawing too much power. Remove the USB device.
−
SP 35:50, LP 151h
“SP”, “LP” and the numbers are
examples.
Available space on the HDD or disc.
The example “SP 35:50” is displayed when less than 100 hours are
available and the example “LP 151h” is displayed when over 100 hours
are available.
“SP” and “LP” are recording modes, “35:50” means “35 hours 50 minutes”
and “151h” means “151 hours”.
−
UNSUPPORT
You have inserted a disc the unit cannot play or record onto.
16, 17
You tried to operate with a non-compatible USB memory.
18
UNFORMAT
You inserted an unformatted DVD-RAM, DVD-RW, +RW, an R,
+R DL or DVD-RW (DVD-Video format) that has been recorded on other
equipment.
Format the disc to use it.
However all the recorded contents on the disc are deleted.
64
F74
The HDMI connection could not be authenticated due to a transfer
malfunction. Consult the dealer where the unit was purchased.
−
F75
The HDMI connection could not be authenticated due to an internal data
malfunction. Consult the dealer where the unit was purchased.
−
U59
The unit is hot.
The unit switches to standby for safety reasons. Wait for about 30 minutes
until the message disappears.
Select a position with good ventilation when installing the unit. Do not
block the cooling fan on the rear of the unit.
−
U61
(When a disc is not inserted) Displays when a malfunction has occurred.
This is displayed when the unit is in the recovery process to return to
normal operation; it is not broken. Once the display disappears you can
use the unit again.
−
U76
HDMI cannot be output because you are connected to a model that does
not support copyright protection.
−
U80, U81, U99
The unit fails to operate properly. Press [
/I] on the main unit to switch the
unit to standby mode. Press [
/I] on the main unit again to turn the unit
on.
−
The message are alternately displayed.
Messages
DMR-EH58EBL.indb 80
DMR-EH58EBL.indb 80
2008/05/19 17:21:24
2008/05/19 17:21:24
