ELB CHECK
ER
RESET PU
SH UP
ELB
POWER SELECTOR
SUPER POWER
MULTI POINT
ELB CHECKE
R
RESET PUS
H UP
ELB
POWER SELECTOR
SUPER POWER
MULTI POINT
- 6 -
(1) Inspection on built in ELB (once a month)
1) Press the Test Button of the ELB Test Button until both
of the ELB RESET Lever come down.
If the ELB is normal, both of the ELB RESET Lever will
come down. The ELB RESET Lever is behind the Front Plate.
If both of the ELB RESET Lever not come down, inform the
dealer of the matter.
2) Push up both of the ELB RESET Lever to reset the ELB.
If one or both of the ELB RESET Lever cannot push up,
inform the dealer of the matter.
(1)
檢查內藏
ELB
（每個月）
1)
按下
ELB
檢查處的試驗鈕以將
ELB
復原控制棒落下，
假如
ELB
是操作正敘，
ELB
的復原控制棒將落下。
ELB
復原控制棒位於機箱後面。
如
ELB
復原控制棒沒有落下，請趕快通知經銷商有關這方面
的事項。
2)
推上
ELB
的復原控制棒。
如
ELB
復原控制棒不能推上，請趕快通知經銷商有關這方面
的事項。
Pressure Relief Device
解壓裝置
ELB CHECKER
RESET PUSH UP
DH-10BM1P
ELB
POWER SELECTOR
SUPER POWER
MULTI POINT
ELB CHECKER
RESET PUSH UP
DH-10BM1
ELB
POWER SELECTOR
SUPER POWER
MULTI POINT
ELB CHECK
ER
RESET PU
SH UP
ELB
POWER SELECTOR
SUPER POWER
MULTI POINT
(1) Note that the hot water temperature will be very high if the
flow rate is excessively reduced.
(1)
請注意：如果水的流量過小，水溫就過熱。
(2) Do not spray water to the equipment, nor put wet towels on it.
(2)
不可向機身噴淋水，及不可在機身上掛下濕潤的毛巾等。
5. PRECAUTIONS /
各項注意
(3) Never install filter assembly at outlet.
(3)
切勿將過濾器安裝於出口。
(3) Filter Unit cleaning.
Clean the Filter Unit with water every week.
Clean the Filter Unit when you feel that hot water
is not drawn normally.
The Filter Unit can be easily removed by turning the
Filter Unit counterclockwise after closing the Main Water Valve.
Tighten it back after washing the Filter Unit.
NOTE : A safety device is incorporated in the
Filter Unit. (Avoid turning this part)
(3)
清洗過濾器組件
清洗過濾器組件的過濾器每隔一星期，
清洗它當你感覺到水流出來有點異常。
過濾器可以容易的取出，先將主水閥擰緊，
跟著，只要把過濾器向反時針方向旋轉則可。
注意： 安全裝置物是合併在過濾器組件的零件。
（避免旋轉這個零件）。
(2) Main body cleaning.
Be sure to switch off the Miniature
Circuit Breaker beforehand.
1) Clean it with cloth moistened.
2) Never use benzine, thinner etc.
(2)
清理機身時
清理維修時，先要確認電流回路斷開器是否斷開。
(1)
用沾濕棉布來擦淨。
(2)
決不可使用揮發油，信納水等
Filter Unit
過濾器
6. MAINTENANCE /
維修
Please make sure the O Ring is not
remove and shall be free from foreign
obstacle to avoid water leaking.
確保
O
環不被移除及免於外來障礙以
避免漏水。
Water Inlet
入水口
ELB RESET Lever (2 pcs)
ELB
復原控制棒（兩個）
Filter Knob
過濾器鈕
ELB Test Button
ELB
試驗鈕
Pressure Relief Device is incorporated to prevent the building up of
excessive water pressure inside the unit due to closed outlet or
incoming water pressure too high. Water will be discharged from the
top of the Filter Knob in case of the Pressure Relief Device is activated,
this is not a sign of any trouble. Adjust the Main Water Valve to cease
the water from flowing out from Pressure Relief Device.
解壓裝置是為了防止因出水口被關閉而造成機體內的水壓過高或
來襲水壓過高。 當解壓裝置啟動時，水將由過濾器鈕上面排出，
這並不是一個故障的跡象。
調整水道的主水閥以停止水由解壓裝置流出。