- 5 -
(1) When the Power Selector Knob
3
is set to “HI”, Power Level is high.
(2) When the Power Selector Knob
3
is set to “MED”, Power Level is medium.
(3) When the Power Selector Knob
3
is set to “LO”, Power Level is low.
(4) When it set to “OFF" the power is cut off and outlet water temperature is same with inlet water temperature.
4. HOW TO OPERATE POWER SELECTOR KNOB /
電量調整鈕的使用方法
(1) Turn on the Main Water Valve
1
.
(2) Switch “ON" the Miniature Circuit Breaker
2
.
(3) Push up both ELB RESET Lever
5
if it is down. (The ELB indicating lamp
lights when the Power Selector Knob
3
is activated).
(4) Set the Power Selector Knob
3
to the desired position.
Turn on the Hot Water Faucet
4
.
Then the ELB Lamp Lights and the equipment operates.
NOTE :
• The water temperature lowers as the volume of water is
increased by opening the Faucet.
• The water temperature rises as the volume of water is
decreased by closing the Faucet.
ELB CHECKER
RESET PUSH UP
DH-10BM1P
ELB
POWER SELECTOR
SUPER POWER
MULTI POINT
2. BEFORE USE /
準備工序
Please engage an authorized dealer or specialist for the installation work. You are requested to check the following points before
using the equipment. If you have any questions or doubts about the equipment, please consult the nearest Panasonic Water Heater
Service Centre.
(1) Is this equipment earthed?
(2) When the aboves are not supplied, immediately ask the shop to install the earth before use.
請委托授權經銷商負責本器的一切安裝工程，安裝後實際使用前，必須確認以下項目。
如果有問題或動作反敘，請征询邻近的
Panasonic
電熱噴水器服务中心。
(1)
該裝置上有無設置接地？
(2)
如果都沒有設置時，使用之前向經銷商店聯系，委托設置。
(1)
請先擰開水道的主水閥
1
。
(2)
啟開電流回路斷開器
2
。
(3)
將ELB的復原控制棒推上
5
，假如在倒下的位置。
（當水流出，ELB指示燈才會點亮。但是，不會點亮如果只是把復原控制棒推上）。
(4)
把電量調整鈕
3
調整到對你所期望的位置。
請擰開熱水龍頭
4
跟著電量指示燈就發亮，組件開始動作。
注意：
•
擰開水龍頭，放大水量，則噴水溫度逐漸降低。
•
相反，隨著擰開水龍頭縮小流量，則噴水溫度逐漸升高。
(1)
當電量調整鈕
3
旋轉到“HI”的位置，電量是在最高的水平。
(2)
當電量調整鈕
3
旋轉到“MED”的位置，電量是在最適度的水平。
(3)
當電量調整鈕
3
旋轉到“LO”的位置，電量亦變低，供給較低溫的水。
(4)
當電量調整鈕
3
旋轉到“OFF”的位置，電量將變零，只流出室內溫度的常溫水。
Push ELB RESET
Lever up if it is down
(2pcs)
將
ELB
的復原控制棒推
上，假如在倒下的位置
（兩個）
3. HOW TO USE /
使用法