background image

19

11 Installation Instruction

11.1. Select The Best Location

11.1.1.

Indoor Unit

• Do not install the unit in excessive oil fume area such as

kitchen, workshop and etc.

• There should not be any heat source or steam near the unit.
• There should not be any obstacles blocking the air

circulation.

• A place where air circulation in the room is good.
• A place where drainage can be easily done.
• A place where noise prevention is taken into consideration.
• Do not install the unit near the door way.
• Ensure the spaces indicated by arrows from the wall, ceiling,

fence or other obstacles.

• Recommended installation height for indoor unit shall be at

least 2.5 m.

11.1.2.

Outdoor Unit

• If an awning is built over the unit to prevent direct sunlight or

rain, be careful that heat radiation from the condenser is not
obstructed.

• There should not be any animal or plant which could be

affected by hot air discharged.

• Keep the spaces indicated by arrows from wall, ceiling,

fence or other obstacles.

• Do not place any obstacles which may cause a short circuit

of the discharged air.

• If piping length is over 7.5 m, additional refrigerant should be

added as shown in the table.

Example: For PC36HKV
If the unit is installed at a 10m distance, the quantity of
additional refrigerant should 75 g ...... (10 - 7.5) m x 40 g/m =
100 g

11.2. Indoor/Outdoor Unit

Installation Diagram

• This illustration is for explanation purposes only.

The indoor unit will actually face a different way.

Model

Piping size Rated 

Length 

(m)

Max.  

Elevation 

(m)

Min. 

Piping 

Length 

(m)

Max. 

Piping 

Length 

(m)

Additional 

Refrigerant 

(g/m)

Gas Liquid

PC36HKV 3/4”

3/8”

5

20

3

30

40

Содержание CS-PC36HKV






















































Отзывы: