background image

Remote control

Do not allow infants and small children to play 

with the remote control to prevent them from 

accidentally swallowing the batteries.

Power supply

Do not use a modified cord, 

joint cord, extension cord or 

unspecified cord to prevent 

overheating and fire.

  

To prevent overheating, fire or electric shock:

• Do not share the same power outlet with 

other equipment.

• Do not operate with wet hands. 

• Do not over bend the power supply cord.

• Do not operate or stop the unit by inserting 

or pulling out the power plug.

If the supply cord is damaged, it must be 

replaced by the manufacturer, service agent 

or similarly qualifi ed persons in order to avoid 

a hazard.
It is strongly recommended to be installed 

with Earth Leakage Circuit Breaker (ELCB) 

or Residual Current Device (RCD) to prevent 

electric shock or fi re.
To prevent overheating, fi re or electric shock:

• Insert the power plug properly.

• Dust on the power plug should be 

periodically wiped with a dry cloth.

Stop using the product if any abnormality/

failure occurs and disconnect the power plug 

or turn off the power switch and breaker.

(Risk of smoke/fi re/electric shock) Examples 

of abnormality/failure

• The ELCB trips frequently.

• Burning smell is observed.

• Abnormal noise or vibration of the unit is 

observed.

• Water leaks from the indoor unit.

• Power cord or plug becomes abnormally hot.

• Fan speed cannot be controlled.

• The unit stops running immediately even if it 

is switched on for operation.

• The fan does not stop even if the operation 

is stopped.

Contact your local dealer immediately for 

maintenance/repair.
This equipment must be earthed to prevent 

electrical shock or fi re.

Prevent electric shock by switching off the 

power supply and unplug:

 -Before cleaning or servicing,

 -When extended non-use, or

 -During abnormally strong lightning activity.

Precaution for using R32 refrigerant

The basic installation work procedures are the same as 

conventional refrigerant (R410A, R22) models.

Since the working pressure is higher than that of 

refrigerant R22 models, some of the piping and 

installation and service tools are special.

Especially, when replacing a refrigerant R22 

model with a new refrigerant R32 model, always 

replace the conventional piping and flare nuts 

with the R32 and R410A piping and flare nuts on 

the outdoor unit side.

For R32 and R410A, the same flare nut on the 

outdoor unit side and pipe can be used.

Models that use refrigerant R32 and R410A 

have a different charging port thread diameter to 

prevent erroneous charging with refrigerant R22 

and for safety.

Therefore, check beforehand. [The charging port 

thread diameter for R32 and R410A is 1/2 inch.]

Be more careful than R22 so that foreign matter 

(oil, water, etc.) does not enter the piping.

Also, when storing the piping, securely seal the 

opening by pinching, taping, etc. (Handling of 

R32 is similar to R410A.)

CAUTION

Indoor unit and outdoor unit

Do not wash the indoor unit with water, benzine, 

thinner or scouring powder to avoid damage or 

corrosion at the unit.

Do not use for preservation of precise 

equipment, food, animals, plants, artwork 

or other objects. This may cause quality 

deterioration, etc.

Do not use any combustible equipment in front 

of the airflow outlet to avoid fire propagation.

Do not expose plants or pet directly to airflow to 

avoid injury, etc.
Do not touch the sharp aluminium fin, 

sharp parts may cause injury.
Do not switch ON the indoor unit when waxing 

the floor. After waxing, aerate the room properly 

before operating the unit.

Do not install the unit in oily and smoky areas to 

prevent damage to the unit.

Do not dismantle the unit for cleaning purpose 

to avoid injury.

Do not step onto an unstable bench when 

cleaning the unit to avoid injury.

Do not place a vase or water container on the 

unit. Water may enter the unit and degrade the 

insulation. This may cause an electric shock.

Do not open window or door for long time during 

operation, it may lead to inefficient power usage 

and uncomfortable temperature changes.

Содержание CS/CU-KU12ZKY Series

































Отзывы: