Palfinger ILUK 33 Скачать руководство пользователя страница 32

Страница: 32 / 43

ILUK 33/44/55/60

Owner’s Manual

Rev.1.5

8.2

Electrical Wiring

– Batteries – Truck/Trailer

*Resettable Circuit Breaker: 150 Amp Min.

Replace with same amperage breaker when necessary.

Ground: For optimal grounding, ground all batteries and power units to the body side rails of the vehicle.

NOTICE: DO NOT attempt to jump in-line fuses with other objects other than the specified fuse.
Do not increase the amperage rating of fuse. Serious harm to the liftgate will result when standard practices are not followed.

Main
Batteries

*Resettable
Circuit
Breaker

Ground

2Ga Power Cable

From Liftgate (+)

2Ga Ground Cable

From Liftgate (-)

In-Line
Fuse

Wires #2 and #4
go to postitive (+)

Wires #1 and Gr/Yl
go to ground (-)

Wiring Diagram

– Truck

*Resettable
Circuit
Breaker

Single
Pole
Socket

Auxiliary
Batteries

Ground

*Resettable
Circuit
Breaker

2Ga Power Cable

From Liftgate (+)

2Ga Ground Cable

From Liftgate (-)

In-Line
Fuse

Wires #2 and #4
go to postitive (+)

Wires #1 and Gr/Yl
go to ground (-)

*Resettable
Circuit
Breaker

Dual
Pole
Socket

Auxiliary
Batteries

Ground

*Resettable
Circuit
Breaker

2Ga Power Cable

From Liftgate (+)

2Ga Ground Cable

From Liftgate (-)

In-Line
Fuse

Wires #2 and #4
go to postitive (+)

Wires #1 and Gr/Yl
go to ground (-)

Wiring Diagram

– Single Pole – Trailer

Wiring Diagram

– Dual Pole – Trailer

Содержание ILUK 33












































Результаты поиска

Содержание ILUK 33

Отзывы:

Похожие инструкции для ILUK 33

Бренды по названию

Популярные бренды

Palfinger ILUK 33, Руководство пользователя

Результаты поиска

Содержание ILUK 33

Отзывы:

Похожие инструкции для ILUK 33

Бренды по названию

Популярные бренды