Palfinger ILUK 33 Скачать руководство пользователя страница 26

Страница: 26 / 43

ILUK 33/44/55/60

Owner’s Manual

Rev.1.5

ELECTRICAL SYSTEM IS PROTECTED BY

A RESETTABLE CIRCUIT BREAKER. SEE

OWNER'S MANUAL AND DECAL LOCATED

AT THE BATTERY.

ELECTRICAL SYSTEM

PROTECTED BY

RESETTABLE CIRCUIT

BREAKER

TO RESET -

PUSH RESET TAB IN

READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS BEFORE USE.

ALWAYS STAND CLEAR

OF PLATFORM AREA

MAXIMUM LOAD CAPACITY

XXXX LBS.

CENTER LOAD ON PLATFORM TO AVOID
PERSONAL OR PROPERTY DAMAGE

1. Improper operation of this lift gate can result in serious personal injury. Do

not operate unless you have been properly instructed, have read, and are

familiar with, the operating instructions. If you do not have a copy of the

instructions please obtain them from your employer, distributor or lesser, as

appropriate, before you attempt to operate the lift gate.

2. Be certain the vehicle is properly and securely braked before using the liftgate.

3. Always inspect this lift gate for maintenance or damage before using it. If

there are signs of improper maintenance, damage to vital part, or a slippery

platform surface, do not use the lift gate. Do not attempt your own repairs,

unless you are specifically trained.

4. Do not overload. See the Mfg. Literature and/or Rating Label on the unit for

the rated load. Remember that this limit applies to both raising and lowering

operations.

5. Each load should be placed in a stable position as near as possible to the

center of the platform.

6. Never allow yourself, a helper, or a bystander to stand in a position where an

unstable load might fall on them. Do not allow any part of your or your helper’s

body to be placed under, through, or around any portion of the moving lift gate,

or in a position that would trap them between any parts when the lift gate is

operated.

7. This lift gate is intended for loading and unloading of cargo only. Do not use

this lift gate for anything but it’s intended use. The lift gate is not equipped

with a back up system to prevent falling in the event of a failure.

BEFORE OPERATING LIFT, BE SURE YOU UNDERSTAND:

LIFT GATE

SHUT-OFF

TO BE TURNED OFF

WHEN LIFT IS NOT

IN USE

DOWN:

Step on switch 1 and hold - wait between one and three seconds

before you step on switch 2.

UP:

Step on switch 2 and hold - wait between one and three seconds

before you step on switch 1. The platform will tilt up to preset

position before raising

If both switches are not activated within three seconds start over.

Read all Decals and Owner's Manual before operating liftgate

Down

Tilt

Lift

Slide

Out

Down

For questions regarding operation call (888) 774-5844

ILUK / ILU

• To operate this liftgate read and understand the

operating decals and manuals.

• Make certain the platform is clear before

operating the lift.

• Liftgate shut-off switch must be turned off when

liftgate is not in use.

• Keep platform in horizontal position when

loading and unloading.

• Do not overload, refer to capacity decals.

Loading Position:

• Lower platform

• Slide out liftgate

• Unfold platform

Storage Position:

• In down position fold up

platform tip

• Slide in liftgate

• Raise platform

Max Capacity

on Platform

Platform

Load

24"

USE HANDLE TO OPEN & CLOSE

ALWAYS STAND CLEAR

OF PLATFORM AREA WHEN

OPERATING THE GATE

Right Side
(Curb Side)

Left Side
(Street Side)

Decal - E

Decal - B

Decal - C

Decal - D

Decal - A

Decal - F

Decal - G

Decal - H

Decal - I

Decal - J

Decal - K

Содержание ILUK 33












































Результаты поиска

Содержание ILUK 33

Отзывы:

Похожие инструкции для ILUK 33

Бренды по названию

Популярные бренды

Palfinger ILUK 33, Руководство пользователя

Результаты поиска

Содержание ILUK 33

Отзывы:

Похожие инструкции для ILUK 33

Бренды по названию

Популярные бренды