Palfinger ILUK 33 Скачать руководство пользователя страница 38

Страница: 38 / 43

ILUK 33/44/55/60

Owner’s Manual

Rev.1.5

8.8 Functional Description of Hydrualics When Operating

The following operating functions are relating to Section 8.6. Please use the schematic to understand the

specific functionality of the ILUK liftgate.

8.8.1

Slide Out Function



As soon as the Motor starts to run, valve S8 is energized.



Oil pressure on input “A” sets exits “Av” and Bv” at the valve block under pressure.



The surface at the end of the

piston rod on input “B” is larger than on the shaft at input “A”.



This creates a stronger force at the piston rod (“B”) than at the shaft (“A”).



This factor forces the cylinder to extend.



The lift gate will slide out to the end of the rails.

8.8.2

Lower Down and Auto Tilt Function



The shift valve S5 at the pump and the solenoid release valves S1 and S2 at the cylinders will get

energized. In addition the leaking down stop valve S11 in the back of the mount frame is also

energized.



The gate is designed to lower down by gravity. It will push the hydraulic oil out of the lift cylinder into

the reservoir. The oil passes the solenoid release valves S1 and S2. It also has to pass the energized

S11 valve in the back of the mount frame and the shift valve S5 at the pump.



When the platform touches the ground the auto tilt function will get activated (B-13).



Solenoid release valves S3 and S4 at the tilt cylinders will be activated.



The existing oil in the tilt cylinder runs back through the energized solenoid release valves S3 and S4

and the energized shift valve S5.



Speed of tilting down will be reduced by passing through the restrictor R5.

8.8.3

Level Out Activity



Motor starts running and S5 valve is energized.



Oil pressure on input “B” sets pressure on exits “BK” at the valve block.



The Oil pressure on exit “BK” at the valve block sets the input “B” at the tilt cylinder on pressure.



The platform will tilt up and get in a level position. When the platform is leveled, the B-15 Platform

sensor shuts down the shift valve S5 and activates the S1 and S2 valves at the Lift Cylinders which

directs the fluid into the Lift Cylinders. This causes the platform to raise.

Содержание ILUK 33












































Результаты поиска

Содержание ILUK 33

Отзывы:

Похожие инструкции для ILUK 33

Бренды по названию

Популярные бренды

Palfinger ILUK 33, Руководство пользователя

Результаты поиска

Содержание ILUK 33

Отзывы:

Похожие инструкции для ILUK 33

Бренды по названию

Популярные бренды