11
Jet Swim Athlete
MA30-1
1 GB
ENGLISH
Th
is
d
oc
um
en
t a
nd
it
s
co
nt
en
ts
a
re
th
e
ex
cl
us
iv
e
pr
op
er
ty
o
f P
ah
lé
ns
a
nd
m
ay
n
ot
b
e
co
pi
ed
,
re
pr
od
uc
ed
, t
ra
ns
m
itt
ed
o
r c
om
m
un
ic
at
ed
to
a
th
ird
pa
rty
, o
r u
se
d
fo
r a
ny
p
ur
po
se
w
ith
ou
t w
rit
te
n
pe
rm
is
si
on
.
Art.no.
Rev.no.
Scale
Designed by:
Approved by:
Revised by: Date
Drawn by: Date
Drawing number
Assembly drawing no.
Surface treatment
part of ISO 2768-1
The tolerance class in accordance with this
E
Box 728, SE-194 27 Upplands Väsby, Sweden
Phone +46 8 59411050, Fax +46 8 59086880
RJ
2019-04-16
plywood montering
19
18
17
16
20
1
11
10
9
8
7
6
5
2
1
2
2
2
3
4
12
14
13
15
Installation
Mount the pump part on a firm surface in a dry space.
Ensure that the space has good ventilation and is provided with drains to prevent flooding.
All mounting of stainless-steel parts shall be carried out with tools intended solely for the respective material to maintain
corrosion resistance. All screws should be greased with Molykote® (supplied).
1.
Make a hole (approx. 457x144 mm) in the pool wall for the enclosure (item 1).
Use the enclosure as a template: mark and drill the four holes on the sides (drill Ø6).
2. Place the enclosure in the hole with the flanges facing the outside of the pool body.
Install with screws (item 2), washers (item 3) and nuts (item 4).
3. Attach the self-adhesive gasket (item 5) to the enclosure.
4.
Mount the wall mat and liner.
5. Fill the pool with water up to 5 cm below the enclosure.
6. Screw (item 8) the fastening frame (item 7) with the rubber gasket (item 6) under-
neath the enclosure with 5 Nm in tightening torque. The screws must be greased.
7. Cut off the liner against the inside of the clamping frame.
8.
Fit the inlet grille (item 10) and the stainless-steel front (item 11) with the screws (item
11) to be greased.
9. Mount the starter hose, see section “Installing the starter hose” on page 13.
10.
Connect the pump (item 19) with the supplied hose socket (item 16), hose (item 17)
and hose clamps (item 18). The pool can then be filled with water to the desired level.
11.
Electrical connection must be carried out by a qualified electrical installer, see section
“Electrical installation”.
NOTE! The pump must never run without water.
Note!
The starter hose must always be laid in a loop 150–200 mm above the water surface.
Never run the pump dry as this will damage the shaft seal.
Electrical installation must be carried out by a qualified electrician and fitted with a residual current device.
Figure 5.
Wooden frame with liner, as seen from above.
1. Installation for thin pool wall with liner
(wood, sheet metal, plastic, etc.)
1. Niche
2. Coundersunk screw M6x30 (4 pcs)
3. Washer (4 pcs)
4. Nut (4 pcs)
5. Self-adhesive gasket
6. Packing
7. Mounting frame
8. Coundersunk screw M5x16 (24 pcs)
9. Screw M4x10 (8 pcs)
10. Inlet grille (3 parts)
11. Front
12. Coundersunk screw M5x20 (2 pcs)
13. O-ring
14. Plug
15. Starter hose (two parts)
16. Hose socket (2 pcs)
17. Hose (2 pcs)
18. Hose clamp (4 pcs)
19. Pump
20. Pool body (plywood)
21. Wall mat
22. Liner