Pacific Sun Kore 7th Скачать руководство пользователя

Страница: 2 / 79

Page 2

Kore 7th Manual / kHLab Edition

Table of Contents

1. Introduction ......................................................................................... 4

1.1. Product Information and Features .............................................................................. 4

1.2. The Kore 7th / kHLab Edition Package ....................................................................... 4

1.3. The Kore 7th / kHLab Device Features ........................................................................5

1.4. kHLab Device Technical Specifications ......................................................................5

2. Kore 7th / kHLab Device installation .................................................. 6

2.1. Proper device setup and installation ...........................................................................6

2.2. Kore 7th Connection Ports ...........................................................................................6

2.3. Tubing and cables connection ...................................................................................10

3. Kore 7th Wi-Fi Communication Network Setup ................................12

3.1. Kore 7th Wi-Fi Network Protection Setup .................................................................12

3.2. Connect Kore 7th to your Internal Wi-Fi Home Network..........................................17

3.3. Kore 7th IP Address Forwarding Setup ......................................................................21

3.4. Kore 7th Virtual Serial Port Installation and Setup ................................................... 24

4. Kore 7th Desktop/Laptop Application Installation ...........................31

4.1. MS Windows Application Installation ........................................................................31

5. Starting the Kore 7th Windows Application ....................................36

5.1. Open and Start Windows Application ...................................................................... 36

5.2. Connection ................................................................................................................. 38

5.3. Dose settings ..............................................................................................................40

5.4. Advanced Dose ...........................................................................................................41

5.5. Manual Control / Calibration ...................................................................................... 42

5.6. Liquid Setup................................................................................................................44

5.7. ATO / Temp config ...................................................................................................... 45

5.8. AWC ............................................................................................................................46

5.9. pH ports ......................................................................................................................48

5.10. kHLab ..........................................................................................................................49

5.11. dKH chart .................................................................................................................... 50

5.12. System .........................................................................................................................51

6. Kore 7th Smart Phone Application Installation ...............................53

6.1. Android Application Installation ................................................................................ 53

7. Starting the Kore 7th Android Application ......................................54

7.1. Open the Android Application ................................................................................... 54

8. kHLab Pumps Calibration and Accuracy Check ..............................56

8.1. Calibration Using the Calibration/Measuring Cylinder ............................................ 56

8.2. Calibration With Precise Digital Scale and Stand/Holder ........................................ 56

8.3. Starting the Channel #1 Calibration Process (

Water Sample

) ................................ 58

Содержание Kore 7th
















































































Результаты поиска

Содержание Kore 7th

Отзывы:

Похожие инструкции для Kore 7th

Бренды по названию

Популярные бренды

Pacific Sun Kore 7th, Руководство пользователя

Результаты поиска

Содержание Kore 7th

Отзывы:

Похожие инструкции для Kore 7th

Бренды по названию

Популярные бренды