Pacific Sun Kore 7th Скачать руководство пользователя

Страница: 51 / 79

Page 51

Kore 7th Manual / kHLab Edition

5.12. System

Doser management

group box

Default settings

Program doser with default settings. We suggest use this button if

your doser after firmware upgrade not work properly.

Clean memory

Erase doser memory. Should be only performed after Pacific Sun

Service request.

Soft reset

Generate reset signal for doser.

Emergency

connect

Should be performed if software can’t connect with doser due

firmware incompatibility. After connection firmware update (with

proper corresponding to software firmware) should be performed.

Memory backup

Generate .mbf file(memory backup file). This file can be send to

our service for diagnose (if something not work properly).

Restore backup

Allow import .mbf file to doser memory.

Calibration backup

Generate file with pump calibration config.

Restore calibration

Allow import calibration backup file to doser memory.

Sensor check

When enabled (check-box) on LCD screen show floating level

sensor status. Can be used for diagnose proper switch connection/

readings.

Содержание Kore 7th
















































































Результаты поиска

Содержание Kore 7th

Отзывы:

Похожие инструкции для Kore 7th

Бренды по названию

Популярные бренды

Pacific Sun Kore 7th, Руководство пользователя

Результаты поиска

Содержание Kore 7th

Отзывы:

Похожие инструкции для Kore 7th

Бренды по названию

Популярные бренды